Jump to content
SAU Community

Midpipe And Transmission Oil Swap


70RTY
 Share

Recommended Posts

On Friday I replaced my stock midpipe with a Challenge Stainless Steel midpipe and swapped the Nissan transmission oil for the Willall product.

Challenge Midpipe:

004.jpg

Willall Transmission Fluid:

005.jpg

The GTR up on the lift:

003.jpg

010.jpg

011.jpg

001.jpg

Old midpipe:

008.jpg

009.jpg

New midpipe installed:

013.jpg

Rear Carbon tray:

007.jpg

As others have reported, the GTR now sounds awesome under acceleration and when blipping the throttle on down changes. The transmission seems quieter with the Willall TM oil.

Link to comment
Share on other sites

Nice man, looks like a nice pipe. I'm really wanting to get a Ypipe upgrade too but worried about excessive drone or sound. Want a nice grown but not a big drone. Is this a good pipe a good sound that isn't annoying with its drone at daily driving? Everything runs smooth after install?

Link to comment
Share on other sites

Everything was fine after install - no warning lights or anything which isn't surprising as the exhaust sensors are located upstream of the midpipe. I chose this midpipe because it had no reports of drone. I would recommend you listen to some midpipes to settle on the one that sounds right for you. I would be happy to meet up if you want to listen to mine.

Link to comment
Share on other sites

Everything was fine after install - no warning lights or anything which isn't surprising as the exhaust sensors are located upstream of the midpipe. I chose this midpipe because it had no reports of drone. I would recommend you listen to some midpipes to settle on the one that sounds right for you. I would be happy to meet up if you want to listen to mine.

Awesome glad to hear everything runs well after install. The R35 so needs a proper exhaust growl and might as well throw a Ypipe on the JDM's make them even more special. I'd really appreciate coming up for a visit to Brisbabe in a couple of weeks once I get my 35 back. (should get my car back this week all going well, got delayed need a Con3 to tweak clutches as there too tight. But appears you were right about someone getting a Con3 in QLD which is a godsend ;-)

Hit you up in PM once i get my car back. Cheer man

Link to comment
Share on other sites

I must say one thing that surprised me was the weight of the factory midpipe. It weights about 20kg, the Willall one I bought weights about 10.

Congrats on the mod, I am getting the trans and diff oil replaced with the willall stuff next week. Good to hear the positive feedback.

Cheers.

Link to comment
Share on other sites

I love to get on the pipe.............. hard to get off once you are on it!

Willall fluid is great too. I am doing their engine & diff oil as well shortly.

Link to comment
Share on other sites

  • 6 months later...

I think the Challenge Mid pipe cost me approx. US$625 plus shipping. Before I bought my car I asked Nissan whether fitting a midpipe would cause issues with my warranty. The salesman informed me that it could affect my warranty.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Much less twat-tastic. CF wheels are too garish for civilised use.
    • From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...