Jump to content
SAU Community

Recommended Posts

Hi Guys,

got some garret 28/60-10's hks gtr's equivilant for sale , just took them off my car as i went for a different set up , had them checked by my mechanic and gcg in sydney they both said turbos in good condition , they have been on car for less then 15,000 km's , they come with standard actuators

Price $2000

I Can send pictures if requested

Please send pms as i dont come on much .

Thanks

Link to comment
https://www.sau.com.au/forums/topic/280885-gtr-turbos/
Share on other sites

I was at gcg today getting a quote for a highflow for my r34, Moei brought these turbos in for inspection. The guy at GCG said they seemed to be in very good condition and if i remember correctly said they were not very easy to come by anymre and retail for $3500. :|

Good luck with the sale buddy, and thats a very nice looking car you got there :starwars:, sounds mean as on idle.

Link to comment
https://www.sau.com.au/forums/topic/280885-gtr-turbos/#findComment-4737752
Share on other sites

Stevo - No Clue man how do i tell i forgot to ask GCG That , all i know is they made 330 kw's on my GTR On 18psi on a unopened motor , my friend same turbos making almost 400kws on a built motor mabye that helps ?

Zee - good to meet ya , very well priced yeh but dont really need them anymore

Link to comment
https://www.sau.com.au/forums/topic/280885-gtr-turbos/#findComment-4737928
Share on other sites

The main ways are; did your stock dumps line up ok? What numbers are on the rear housing (if any)?

Stev-0

Rear housing .62 , i had aftermarket dump pipes and as far as i know they lined up ok ?

Thanks

bump , they need a new home ......

Link to comment
https://www.sau.com.au/forums/topic/280885-gtr-turbos/#findComment-4738794
Share on other sites

Silly question perhaps but the 2860-10's are supposed to be simular to a HKS GTRS right? Well which turbine housing configuration makes them simular to the GTRS, because a 0.62 or 0.8x housing would make quite a diference?

Link to comment
https://www.sau.com.au/forums/topic/280885-gtr-turbos/#findComment-4741991
Share on other sites

Silly question perhaps but the 2860-10's are supposed to be simular to a HKS GTRS right? Well which turbine housing configuration makes them simular to the GTRS, because a 0.62 or 0.8x housing would make quite a diference?

Hey GTRNUR good question ,

as far as i know and i did ask GCG They told me that power wise there isnt much difference between the 2 rear housings , infact he told me .82 rear housing makes a little more power but also has more lag , in terms of which one is similar to hks gtr's configuration i cannot tell you .

Thanks

Link to comment
https://www.sau.com.au/forums/topic/280885-gtr-turbos/#findComment-4742693
Share on other sites

Hey GTRNUR good question ,

as far as i know and i did ask GCG They told me that power wise there isnt much difference between the 2 rear housings , infact he told me .82 rear housing makes a little more power but also has more lag , in terms of which one is similar to hks gtr's configuration i cannot tell you .

Thanks

GT-RS have .64 rears

cheers

Lee

Link to comment
https://www.sau.com.au/forums/topic/280885-gtr-turbos/#findComment-4745408
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
    • What HVAC actuator is under the steering wheel? Do you mean on the RHS of the centre console, immediately to the left of your shin? If so, then yes, it is probably that one, because that is the mode door actuator, and from what I know, it's still a pain in the arse to replace. I don't know about whole dash out, but you certainly have to rip into the centre console section. I don't know if it's covered in the workshop manual, as I haven't spent much time looking at those parts of it. (and by "the workshop manual, I mean the R32 GTR one, which is the most comprehensive one we have, and it should be similar enough between that and later cars to serve as a guide).
    • ...oops. forgot the TCU end...
    • No I got mine from a friend that had fabricated one … but I had to fit it to my setup which was a hks turbo setup. His was a Garrett -7. So one of my turbos was not a flange for one side … then I had a leak in the welds I had to find a weld shut … in the end the setup was decent priced but I spent a lot to get it fitted. A couple companies I checked would make it but you’re talking 7-9k aud with titanium. No joke mine was 6-7k even second hand after I had to fit it in Hong Kong … labour is expensive here. 
    • I'd just like to restate that I don't think anyone here is actually hating I recently sold a car part to a guy who was building a forged auto R34, with MV stall and aiming at ~450kw. I told him that I'm him, from the future and to stop after it explodes once. I told him I knew he won't listen the first time, and that's fine. But if my predictions do come true - Change direction faster than I did. I also said it's probably no coincidence that the dyno plot of a reliable turbo engine starts to look a lot like a N/A motor. :p
×
×
  • Create New...