Jump to content
SAU Community

R32 Obd Protocol

blinko
 Share

Recommended Posts

blinko Proficient

blinko

Posted
Posted

Im trying to find out what protocol an R32 gts-t OBD would use? does anyone know, or know where i can find out?

Also can anyone tell me what information is available from the OBD, or any good sites where i can find this information in detail?

I need this info for an engineering project i am currently building.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/281363-r32-obd-protocol/
Share on other sites
REDGTT Grand Master

REDGTT

Posted
Posted

Signal protocols

There are five signalling protocols currently in use with the OBD-II interface. Any given vehicle will likely only implement one of the protocols. Often it is possible to make an educated guess about the protocol in use based on which pins are present on the J1962 connector:

* SAE J1850 PWM (pulse-width modulation - 41.6 kbaud, standard of the Ford Motor Company)

o pin 2: Bus+

o pin 10: Bus–

o High voltage is +5 V

o Message length is restricted to 12 bytes, including CRC

o Employs a multi-master arbitration scheme called 'Carrier Sense Multiple Access with Non-Destructive Arbitration' (CSMA/NDA)

* SAE J1850 VPW (variable pulse width - 10.4/41.6 kbaud, standard of General Motors)

o pin 2: Bus+

o Bus idles low

o High voltage is +7 V

o Decision point is +3.5 V

o Message length is restricted to 12 bytes, including CRC

o Employs CSMA/NDA

* ISO 9141-2. This protocol has a data rate of 10.4 kbaud, and is similar to RS-232. ISO 9141-2 is primarily used in Chrysler, European, and Asian vehicles.

o pin 7: K-line

o pin 15: L-line (optional)

o UART signaling (though not RS-232 voltage levels)

o K-line idles high

o High voltage is Vbatt

o Message length is restricted to 12 bytes, including CRC

* ISO 14230 KWP2000 (Keyword Protocol 2000)

o pin 7: K-line

o pin 15: L-line (optional)

o Physical layer identical to ISO 9141-2

o Data rate 1.2 to 10.4 kbaud

o Message may contain up to 255 bytes in the data field

* ISO 15764 CAN (250 kbit/s or 500 kbit/s). The CAN protocol is a popular standard outside of the US automotive industry and is making significant in-roads into the OBD-II market share. By 2008, all vehicles sold in the US will be required to implement CAN, thus eliminating the ambiguity of the existing five signalling protocols.

o pin 6: CAN High

o pin 14: CAN Low

blinko Proficient

blinko

Posted
  • Author
Posted
Signal protocols

There are five signalling protocols currently in use with the OBD-II interface. Any given vehicle will likely only implement one of the protocols. Often it is possible to make an educated guess about the protocol in use based on which pins are present on the J1962 connector:

* SAE J1850 PWM (pulse-width modulation - 41.6 kbaud, standard of the Ford Motor Company)

o pin 2: Bus+

o pin 10: Bus–

o High voltage is +5 V

o Message length is restricted to 12 bytes, including CRC

o Employs a multi-master arbitration scheme called 'Carrier Sense Multiple Access with Non-Destructive Arbitration' (CSMA/NDA)

* SAE J1850 VPW (variable pulse width - 10.4/41.6 kbaud, standard of General Motors)

o pin 2: Bus+

o Bus idles low

o High voltage is +7 V

o Decision point is +3.5 V

o Message length is restricted to 12 bytes, including CRC

o Employs CSMA/NDA

* ISO 9141-2. This protocol has a data rate of 10.4 kbaud, and is similar to RS-232. ISO 9141-2 is primarily used in Chrysler, European, and Asian vehicles.

o pin 7: K-line

o pin 15: L-line (optional)

o UART signaling (though not RS-232 voltage levels)

o K-line idles high

o High voltage is Vbatt

o Message length is restricted to 12 bytes, including CRC

* ISO 14230 KWP2000 (Keyword Protocol 2000)

o pin 7: K-line

o pin 15: L-line (optional)

o Physical layer identical to ISO 9141-2

o Data rate 1.2 to 10.4 kbaud

o Message may contain up to 255 bytes in the data field

* ISO 15764 CAN (250 kbit/s or 500 kbit/s). The CAN protocol is a popular standard outside of the US automotive industry and is making significant in-roads into the OBD-II market share. By 2008, all vehicles sold in the US will be required to implement CAN, thus eliminating the ambiguity of the existing five signalling protocols.

o pin 6: CAN High

o pin 14: CAN Low

thanks for the infor, R32's are OBDI Correct?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GabsReDeal
      New owner of a Skyline R32 GTS

      By GabsReDeal · Posted

      Thanks for your insight, it being basically useless will impact my decision for sure. I thought it may help the engine breath better I guess. But then again, I have also been told that tuning an RB20DE is also not worth it. Exactly, we follow EU Regulations. There is a bit more leeway on older vehicles. My Porsche 924 came without a cat from factory and managed to pass, they still mentioned that I have quite high emissions on it though.
    • soviet_merlin
      City of Casey - This is obscene!

      By soviet_merlin · Posted

      My apologies, I stand corrected. Thanks for registering to mention this! And thank you for actually reaching out to the council to clarify. This is the sensible thing to do and the opposite of what I was alluding you were doing. I may have seen too much outrage and hate being fueled on the internet and it has made me a somewhat cynical old man. Sometimes it is easy to forget that there are real people behind websites and accounts. In my defence, CarExpert and CarExplore do read quite similarly at a glance. I shall try and do better in the future. (Please stick around to get the latest scoops on dealing with old Nissan shitboxes )
    • GTSBoy
      New owner of a Skyline R32 GTS

      By GTSBoy · Posted

      Don't bother. The poor little RB20 doesn't make enough gas flow to challenge the flow capabilities of even the littlest cat, and you won't make any extra power, and all you'll do it soot up your rear bumper. Plus....is Malta not runing under Euro regs?
    • Duncan
      Smoothline aka Matthew stone

      By Duncan · Posted

      Hey Daniel, sorry to hear that and thanks for posting up for us at a really hard time I only knew SmoothLine through the forums, we never met as we are based in different states, but when he was most active on here he was quite a while back so not many of the current crowd might remember him. I am pretty sure he was active in the Queensland SQU club but that is defunct now too (times are changing and we are all getting older). Farewell SmoothLine!    
    • ValgeKotkas
      R34 manual conversion wiring

      By ValgeKotkas · Posted

      Turns out depending on whether the car was equipped with TCS or not there are different signals coming to the dash, meaning there are different speedo clusters.  Wired in a speedo calibrator box from aliexpress and now works fine. 
×
×
  • Create New...