Jump to content
SAU Community

Vic: Work Equip M1 Wheels. 18x9 (like New)

DRFT31
 Share

Recommended Posts

DRFT31 Experienced

DRFT31

Posted
Posted (edited)

Hi guys recently returned my car to stock and will be keeping it that way. There for my beloved wheels are for sale.

Work Equips M1's (Made in Japan) 3 piece wheel.

*Rear - 18x9inch offset +35

*Front - 18x8inch offset +30

Tires are (Nankang Ultra Sport NSII 265/35/R18) on rear which are just above the indicator line

& Nankang Ultra Sport NSII 235/40/R18 on front which are 80% above indicator line.

Rims are 5*114.3 stud pattern.

These sit absolutely perfect on my r34 gt-t the widest you can go before you have to start rolling guards etc.

These wheels are like buying NEW, included are also center caps, even original work air pressure caps which were in plastic till a couple of weeks ago.

Not a scratch to be seen.

Selling for $1950.

Paid a lot more than this when i bought them brand new last year.

Wheels are located in thomastown, melbourne.

Pm me with any questions. Cheers.

3-11.jpg

Edited by DRFT31
DRFT31 Experienced

DRFT31

Posted
  • Author
Posted

Pm's replied.

Truly a beautiful set of wheels, someone that knows wheels and needs a set will not be disappointed when these go on. Will set your car off.

Will get some more pics up tomorrow, with center caps etc.

Btw champ side skirts are the Original Nissan Option Aero Type.

DRFT31 Experienced

DRFT31

Posted
  • Author
Posted
Nice wheels. Keen to swap with any of mine?

Sorry champ just want to sell for the time being. Thanks for the offer thou.

Here are the pics as promised.

rims.jpg

center-cap.jpg

rear-1.jpg

front.jpg

front-t.jpg

rear-r.jpg

DRFT31 Experienced

DRFT31

Posted
  • Author
Posted
Great wheels these are, would finish a car off nicely.

Cant believe there still here.

Free bump :)

Thanks champ, still for sale i also cant believe it. Everyone must be buying cheap Chinese copies from places like THE TYRE FACTORY. :)

DRFT31 Experienced

DRFT31

Posted
  • Author
Posted
Thanks champ, still for sale i also cant believe it. Everyone must be buying cheap Chinese copies from places like THE TYRE FACTORY. :P

Bummmmmmmmmmmmmmmmmmpppppppppppppppp

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R34 Gtt Wheel Offset Advice

      By GTSBoy · Posted

      What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • silviaz
      R34 GTT idle problem

      By silviaz · Posted

      I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • Kinkstaah
      R34 Gtt Wheel Offset Advice

      By Kinkstaah · Posted

      This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • AdiR34
      R34 Gtt Wheel Offset Advice

      By AdiR34 · Posted

      Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...