Jump to content
SAU Community

Recommended Posts

Hey forum I am having an issue with my car overheating and was wondering if anyone can give theories why. I never had heating issues with my normal radiator with clutch fan, but I took it out to install an aluminum dual core I got on a deal. Now the car overheats during normal driving in the daytime. It overheats to the point where hot water bubbles out of the overflow bottle and the stock temp gauge is right below the mark before the H on the gauge.. I have driven it extremely hard in the night time and it didn't overheat, or I just have not driven it long enough, but I think I did as it was driven hard. It just seems to overheat in the daytime under normal driving conditions. I have a 16" electric fan attached to the radiator for cooling without shroud. Can anyone give suggestions as to why it is overheating now with a bigger radiator installed?

Link to comment
https://www.sau.com.au/forums/topic/281403-overheating-heating-issue-r33/
Share on other sites

You may have a air lock in the system.... Just a thought does happen if they are not filled correctly...

Try this:

Start your engine, but leave the radiator cap off so the pressure doesn't build up.

Let the engine run until it reaches its operating temperature.

Turn on your heater and set the temperature control to hot. This will circulate the coolant and any air in the heater lines and core.

Check the level of the coolant. You may find that the level has gone down some. How did that happen? The air trapped in the radiator kept the level artificially high; when this air was released, it opened up more space in the radiator, and allowed more antifreeze into the system. Add more water and antifreeze, in the same 50/50 ratio, to fill the space left by the bled-out air.

As the air bleeds out, the coolant may bubble and spit from the opening on top of the radiator. Use caution--that coolant is hot.

If this does not work check thermostat but i would say thats ur problem.

  • 2 weeks later...

depending on the front mount (if you have one) you could have it restricting flow to the radiator, some aftermarket ones due tend to create a host of cooling problems especially on the track, but go through the basics first, check coolant level and look for leaks/blockages within the radiator...

I have a 16" electric fan attached to the radiator for cooling without shroud.

:O

Just had my dual core installed, retained the stock shroud and my temps are about 13-15 degrees lower at all times...

:(

end thread.

Edited by gunmetalgrey

gunmetalgrey was the first person to pic up the problem. without the shroud the fan isn't work properly. it is probably only working at 50%, if that. most of the cooling comes from the ends of the fan blades as they are traveling faster then the centre of the fan (same rpm, but at a faster speed). without a proper shroud the fan can just suck air from around the outside of the radiator. personally i, and many others, think that the stock clutch fan works better than most thermos.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...