Jump to content
SAU Community

Value Of R35 Engine And Transmission

[200]

By [200],
in R35 GTR

 Share

Recommended Posts

LSX-438 Mentor

LSX-438

Posted
Posted

I have heard notional figures of AU$45k for the transmission and AU$75k for the engine (new prices) regardless of IF they can be purchased. Not that you would buy a crate motor for $75k (if you could) you would instead build something better etc.

If you have need of one and can get it cheap, grab it!

LSX-438 Mentor

LSX-438

Posted
Posted
  bigmikespec said:
LSX-438, happen to know what a set of brakes are? Endless do a sweet adaptor kit to fit them to an older series R32/33/34 GTR.

If you were to ask for a complete OEM Nissan pad and rotor swap, i believe it will be in the vicinity of $8000 to $10,000 (and that doesnt include calipers nor lines). A full brake system would surely be $20k or more. This is for ordinary cast iron & cross drilled rotors mind you. However most people are buying aftermarket pads and rotors, which are about half these prices (and better spec too). If you have an OEM motor/gearbox/brake system and want to offload it, PM me please.

bigmikespec Veteran

bigmikespec

Posted
Posted
  LSX-438 said:
If you have an OEM motor/gearbox/brake system and want to offload it, PM me please.

I wish...

I asked the question to see if it would be worth buying the R35 calipers themselves along with some Endless adaptors and some aftermarket discs. That would be a sweet stopping package for a 200kg lighter older series GTR (like mine).

Sorry, off topic.

[200] Mentor

[200]

Posted
  • Author
Posted
  LSX-438 said:
If you were to ask for a complete OEM Nissan pad and rotor swap, i believe it will be in the vicinity of $8000 to $10,000 (and that doesnt include calipers nor lines). A full brake system would surely be $20k or more. This is for ordinary cast iron & cross drilled rotors mind you. However most people are buying aftermarket pads and rotors, which are about half these prices (and better spec too). If you have an OEM motor/gearbox/brake system and want to offload it, PM me please.

So if something like this was to be wrecked you might be interested in some parts?

gtr01.jpg

gtr02.jpg

[200] Mentor

[200]

Posted
  • Author
Posted
  dirty180driftor said:
expensive.. weeeeee

Hey idiot, leave the stupid comments out of the thread - their not welcome here.

Judging by the posts it looks as though you're trying to get your post count up - typical. You're not contributing anything at all,

eg

Exhibit 1

Exhibit 2

Exhibit 3

:) :) :)

Don't reply with shit that doesn't contribute!!

nugzy31 Proficient

nugzy31

Posted
Posted

good luck with trying to get it over here mate....im sure if you did, youd basically be able to name your price on anything in it....plus the running gear would be an awesome retro fit into something like a 240/260z :P

Beer Baron Grand Master

Beer Baron

Posted
Posted

yes we looked at buying it must be 6 months ago or more now. hopefully it's been well stored and is still in good condition. I thought it sold on ebay US?

the stuff is only worth what someone is willing to pay. but consider you could buy a wreck in japan for around $40K (or less) and import that as a parts car and I'd consider very carefully before you spend any decent time or money bringing it out here hoping to get $100K+ for all the bits.... JDM wreck would also be more desirable as it's RHD. also, that car was pretty heavily crashed, there have been a few wrecks around with less damage going for pretty fair money.

Marlin Grand Master

Marlin

Posted
Posted
  nugzy31 said:
good luck with trying to get it over here mate....im sure if you did, youd basically be able to name your price on anything in it....plus the running gear would be an awesome retro fit into something like a 240/260z :P

Oh my young friend.... if only you knew how difficult that task would be. You'd swear these 35's have a brain of their own, they know what you're doing to them, even without a battery in them! lol

beefcake4000 Apprentice

beefcake4000

Posted
Posted
  nugzy31 said:
good luck with trying to get it over here mate....im sure if you did, youd basically be able to name your price on anything in it....plus the running gear would be an awesome retro fit into something like a 240/260z :)

someone do that please!!!

i couldn't see that black wreck fetching more than 25k

are you in the states? if not id get someone who has half a mechanical brain to check it out, and id assume with the new GTR a multimeter would come in handy to check all the electrics.

[200] Mentor

[200]

Posted
  • Author
Posted
  beefcake4000 said:
someone do that please!!!

i couldn't see that black wreck fetching more than 25k

are you in the states? if not id get someone who has half a mechanical brain to check it out, and id assume with the new GTR a multimeter would come in handy to check all the electrics.

Being done ...

I might just bring the engine, transmission and brakes over and see how things go from there. It's all that's really useful on the black one.

Munro Experienced

Munro

Posted
Posted

Dude. Just put a price on it & see what happens. No-one here will put there hand up unless you put your balls on the wall & see what happens. Looks like a gamble to me. These things are that fast I dont think it will be long before we see a few local ones on the market like that (of course I hope not - but lets wait & see)

20 years to catch up? Hmmm. Didnt see Porsche at Bathurst 20 years ago. (But I was too busy drag racing Holdens back then to care anyway!!!)

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...