Jump to content
SAU Community

Recommended Posts

Hey All

I have been registerd on the forums for abit of time not, come on every now and then. I though id tell abit about my self. Im Zaff I drive a Ford XR6 Turbo BF MkII Sedan. I love cars, basicly spend any of my spare time on 'em. For a while ive been thinking about making a full proper drift car. Something like an R33 gts-t geared up with Plazmaman gear in the engine, with a hi mount GT3540R charger. But still looking for the right car. Does anyone have drift spec cars on here where I could cheak out info on? And how much power can the standard manual gearbox handle before it needs to be strengthened?

I know I shouldn't really post this stuff up as its a Nissan Skyline forum and NOT a Ford XR6T but just incase some are wondering or WA people might have seen me around...

Engine

-Plazmaman 1000HP Intercooler.

-Plazmaman 3" Cold Side Piping.

-Plazmaman 2.5" Hot Side Piping.

-Plazmaman 4" CAI Intake off Turbo into closed box with Odyssey battery.

-Turbosmart Megasonic BOV.

-12 PSI Actuator and ported waste gate/flapper mod.

-60lb Siemens Deka Injectors.

-Walbro Fuel Pump.

-XCAL 3.

Exhaust:

-4" Avalanche Dump Pipe.

-5" 100Cell Custom Forged Cat.

-Twin 2.5" Pacemaker cat-back quad exhaust system with 3" tips.

Exterior:

-XR8 bonnet.

-Typhoon front bar.

-Typhoon/GT side skirts.

-GT back bar.

-GT wing.

-20" Lenso wheels 20x8.5 front and 20x10 rear With Kumho KU31 Ecsta SPT in 275/30/20Rear and 225/35/20 Front

-SL Front and SSL King Springs

Its running 352.7RWKW on 15psi street tune.

SDC10040.jpg

SDC10023.jpg

SDC10012.jpg

SDC10044.jpg

SDC10103.jpg

SDC10001.jpg

Plans are Getting some new a Plenum and some engine bling. But depending how I go with the drft car, if I can find a chassie for the correct price, Ill can it and work on the Drfit car sooner.

If anyone has any specific info I should be aware of for setting up a drift car with the R33's id aprecheat it if they could sent me a PM.

Zaff ;)

Edited by rated x
Link to comment
https://www.sau.com.au/forums/topic/281530-hey/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • does anyone know tie rod torque setting and anti roll bar for r34? Is there a workshop which shows various components torque setting?
    • Hi    have purchased pair of eibach wheel spacer as I couldn’t fit set of wheels I bought for my car due to it catching caliper.   I know I need to cut the bolts on my discs so they sit flush with the nut supplied but the nut doesn’t sit all the way into the groove meaning wheel would not directly fit onto the spacer rather the nuts. Any thoughts?   See pic   https://ibb.co/VJK5w5G
    • Nah. There's not shit tonnes of pressure in there. Just drill with a 1.5mm drill or something equally tiny. When the drill goes all the way through thee gas will start to come out, but with such tiny path through the flutes of the drill bit, it won't be at all dangerous. You can be as paranoid as you like from then on. I'd just pull the drill out while keeping my face out of the line of fire. But then, I spend half my time looking into pressurised furnaces. So my risk acceptance is somewhat higher than most!
    • Been needing a new clutch for a while, but holding off because of life tingz and adulting. But... Being of Asian descent, I can't pass on a good sale, especially everyone else is selling it for $2k+ (JJR has it for $1799). Really on the fence on this one, because the unsprung version of this is $1281 via Shitbox (Sparesbox) and the sprung version is quite a bit more (no idea why Shitbox doesn't offer them). Ending up just sending it and getting the twin sprung organic. Mainly because I wanted the car to be nice to drive and didn't want to make it more of a shitbox than it already is.    
    • It was the pressure I was worried about. @GTSBoy does drilling them pose any problems?
×
×
  • Create New...