Jump to content
SAU Community

Will Do-luck Kit Fit R34 4 Door

TR34SON

By TR34SON,
in Exterior & Interior Styling

 Share

Recommended Posts

MissR34 Grand Master

MissR34

Posted
Posted

yes the front bar should fit no worrys, its really only the side skirts and maybe the rear bar that you could have issues with (the side skirts definelty wont fit unless made for a 4 door)

Kranker Collaborator

Kranker

Posted
Posted

the one in the pic is on a GTR, and i dont think Do Luck make a version for the GTT, but i may be wrong on this

so basically, no, the front bumper wont fit your 4 door. unless you fit a GTR bonnet and front guards

you may however find someone making a copy of the kit that does fit a GTT

steveo_r33 Proficient

steveo_r33

Posted
Posted

where do you buy them in NSW? Do you have to order internationally from www.do-luck.co.uk? If you buy the GTR Kit from this website, as they don't have a GT-T kit, If you sourced GTR front guards and a GTR 34 Bonnet. Would they go together perfectly?

What about the rear bar / skirts without having the flared rear on a GT-T.

Kranker Collaborator

Kranker

Posted
Posted (edited)

with the gtr front guards, bonnet, and hinges (and propably other parts, do a search for what is needed) the front bumper should fit

but be prepared to spend $$$

the side skirts and rear bumper will not fit.

you will need gtr rear guards and maybe other bits and pieces.

there are a few topics floating around here by guys who have gone through the process of fitting GTR bodykits to GTTs, they are worth a look before you go any further

IMO you are better off looking for a GTT copy of the kit

Edited by Kranker

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • PLYNX
      BCNR33/ECR33 Door corner piece replacement

      By PLYNX · Posted

      Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • BourneToLive
      R32 GTR Park lights issue

      By BourneToLive · Posted

      So was there a solution to this problem? I’m having this issue now. 
    • Duncan
      Beers and skylines Fatz style

      By Duncan · Posted

      not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
    • Duncan
      BCNR33/ECR33 Door corner piece replacement

      By Duncan · Posted

      I haven't replaced that, but I have had the doors apart on the r32 a couple of times The door skin will be held on by a combination of clips and bolts, just take it slowly and make sure all the sneaky hidden bolts are out Once the skin is off you should be able to pop that piece off pretty easily, looks like there are only 2 bolts holding it on
×
×
  • Create New...