Jump to content
SAU Community

A'pexi Bolt On Turbo And Suction Kit + Injectors

Bliksem
 Share

Recommended Posts

Bliksem Veteran

Bliksem

Posted
Posted

A'PEXi Turbo Model AX53B70 P25 (Basically an equivelant to a HKS GTRS) Have had the exhaust housing ceramic coated in black to keep temps down.

20,000kms old Purchased through Greenline 2 years ago. Still as good as new no shaft play ready to bolt on. Selling as I have changed to a GT35R, will also throw in a custom stainless dump pipe.

$1650

CIMG1984.jpg

CIMG1988.jpg

A'PEXi Super Suction Kit

Aluminium Hard pipe to replace the rubber intake hose between the AFM and the turbo, Hard to find.

$180

CIMG1985.jpg

Also Have a set of 6 S15 injectors 470cc purchased from Deatschwerks also 20,000kms old Asking $380

All items located in Griffith NSW. Willing to post.

Bliksem Veteran

Bliksem

Posted
  • Author
Posted

I made 250kw at 14psi, turbo is rated at 380ps, so capable of more. Trent as Status tuning told me he has seen these make close to 300kw on an SR20.

I have since discovered I have a large exhaust restriction which would have been limiting the potential of this turbo on my setup.

sparco33 Contributor

sparco33

Posted
Posted
I made 250kw at 14psi, turbo is rated at 380ps, so capable of more. Trent as Status tuning told me he has seen these make close to 300kw on an SR20.

I have since discovered I have a large exhaust restriction which would have been limiting the potential of this turbo on my setup.

pm sent for injectors. will buy.

john-e boi Mentor

john-e boi

Posted
Posted (edited)

definantly consider the Super Suction kit sold if falls through. also interested in the turbo, straight bolt on? is there everything needed to bolt onto a rb25det? will take both off you if possible. thanks

Edited by john-e boi
colesy_skyline r32 Enthusiast

colesy_skyline r32

Posted
Posted

hey mate.. i am interested in the injectors..

i want them for my r32 gtst..

will the fit straight into standard rail??

and will i need resister pack??

please pm me and let me know - am very keen

ben

JKR-32 Proficient

JKR-32

Posted
Posted

if ur 32gtst is still an rb20, then no, they wont fit ur standard rail. s15 injectors are side feed like rb25's. rb20 and rb 26 are top feed.

ps. i'm keen on the injectors.. would u do cod? as i'm in brisbane.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
    • GTSBoy
      AC not coming from top vents

      By GTSBoy · Posted

      What HVAC actuator is under the steering wheel? Do you mean on the RHS of the centre console, immediately to the left of your shin? If so, then yes, it is probably that one, because that is the mode door actuator, and from what I know, it's still a pain in the arse to replace. I don't know about whole dash out, but you certainly have to rip into the centre console section. I don't know if it's covered in the workshop manual, as I haven't spent much time looking at those parts of it. (and by "the workshop manual, I mean the R32 GTR one, which is the most comprehensive one we have, and it should be similar enough between that and later cars to serve as a guide).
    • dbm7
      Shifting questions

      By dbm7 · Posted

      ...oops. forgot the TCU end...
    • Sleepergm
      Custom titanium intake

      By Sleepergm · Posted

      No I got mine from a friend that had fabricated one … but I had to fit it to my setup which was a hks turbo setup. His was a Garrett -7. So one of my turbos was not a flange for one side … then I had a leak in the welds I had to find a weld shut … in the end the setup was decent priced but I spent a lot to get it fitted. A couple companies I checked would make it but you’re talking 7-9k aud with titanium. No joke mine was 6-7k even second hand after I had to fit it in Hong Kong … labour is expensive here. 
    • Kinkstaah
      NC MX5

      By Kinkstaah · Posted

      I'd just like to restate that I don't think anyone here is actually hating I recently sold a car part to a guy who was building a forged auto R34, with MV stall and aiming at ~450kw. I told him that I'm him, from the future and to stop after it explodes once. I told him I knew he won't listen the first time, and that's fine. But if my predictions do come true - Change direction faster than I did. I also said it's probably no coincidence that the dyno plot of a reliable turbo engine starts to look a lot like a N/A motor. :p
×
×
  • Create New...