Jump to content
SAU Community

Recommended Posts

it only kicks in around 80kph as Aaron has said. its basically an electronic actuator (motor) that controls a steering rack attached to the back of the rear subframe and is liked to the rear of the wheel hub with a toe arm. on the R32 & S13 models it was a hydraulic setup driven off the power steering pump. it turns the rear wheels only by approx 0.7 deg from center, so if your where going around a right hand bend you wheels would be something like this:

front wheels // //

rear wheels \\ \\

when you install a HICAS lock bar you remove the actuator/rack and put a solid bar in between the two toe arms to hold the rear wheel toe where you want it.

edit: beat me with a much better diagram MIKE lol

Edited by QWK32
Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4753292
Share on other sites

HICAS is a very complex system, that is way over what most people think it is.

It helps to make a car feel shorter & more nimble, and helps to damp Yaw effect.

A long wheelbase car is easier to control but slower to turn. Rear wheel steering helps to turn the vehicle.

It has been heavily critisized for making the rear end feel loose, vauge and unnatural.

Lots of HICAS systems get taken off cars, mostly because owners do not fully understand what it is about.

It is there to make the car drive faster.

As you enter the corner the rear of the car actually gets kicked out, which reduces understeer, if you stay hard on the accelerator, as the car reaches the apex, the steering, G-sensors and throttle position will let the car "know" that it is at the apex, the rear wheels will come into phase and the car will steer straight though the apex, to take the fastest line through the corner.

It's kinda like taking a drifters line without drifting.

Your car should have the same system as the R34, which is also a model following control system.

It is pre-programmed to follow cornering models. It is not just feedback based.

If you really want to find out more about, and get a new admiration for our favorite car (sorry not the Stagea) get the book Nissan GTR by Alex Gorodji. Some of the above is taken from the book.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4753764
Share on other sites

simple diagram

how_hicas_works.gif

i really hope it doesnt work that way, thats very dangerous!! if the rear wheels are turning in the same direction as the front wheels, instead of the opposite, then u r in big trouble if the front doesnt turn in. in an understeer situation, that would have the rear wheels turning u straight off the road!!

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4753813
Share on other sites

HICAS is a very complex system, that is way over what most people think it is.

It helps to make a car feel shorter & more nimble, and helps to damp Yaw effect.

A long wheelbase car is easier to control but slower to turn. Rear wheel steering helps to turn the vehicle.

It has been heavily critisized for making the rear end feel loose, vauge and unnatural.

Lots of HICAS systems get taken off cars, mostly because owners do not fully understand what it is about.

It is there to make the car drive faster.

As you enter the corner the rear of the car actually gets kicked out, which reduces understeer, if you stay hard on the accelerator, as the car reaches the apex, the steering, G-sensors and throttle position will let the car "know" that it is at the apex, the rear wheels will come into phase and the car will steer straight though the apex, to take the fastest line through the corner.

It's kinda like taking a drifters line without drifting.

Your car should have the same system as the R34, which is also a model following control system.

It is pre-programmed to follow cornering models. It is not just feedback based.

If you really want to find out more about, and get a new admiration for our favorite car (sorry not the Stagea) get the book Nissan GTR by Alex Gorodji. Some of the above is taken from the book.

i would have to agree, i had a loaner R33 sedan with hicas, and for a big heavy car, this thing handled quite well and could be easily thrown around. i have no idea why people complain about hicas so much. i think they hear that one person doesnt like it and calls it useless, then it MUST be. if it WAS useless, car manufacturers wouldnt be equipping cars with it.......

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4754142
Share on other sites

I think the biggest complaints about HICAS come from anyone who has a dedicated track/drift car, or frequents a track for racing or drifting. And because every second person thinks of themselves as a race car driver or drifter they remove it based on what the real race driver and drifters have said.

Personally I liked the HICAS on my old 32 but can vouch for the fact that once the tail end is out there, it's too easy to over correct because the HICAS system is also assisting the turn.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4754451
Share on other sites

You have to love the original HICAS implementation in the R31's - it had a couple of rams and flexed the entire K-frame on it's bushes!

4WS seems to have dropped off the radar these days, possibly due to it's mechanical complexity vs. what you can to with ESP and it's broader safety benefits.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4754683
Share on other sites

i really hope it doesnt work that way, thats very dangerous!! if the rear wheels are turning in the same direction as the front wheels, instead of the opposite, then u r in big trouble if the front doesnt turn in. in an understeer situation, that would have the rear wheels turning u straight off the road!!

open your eyes before your mouth please

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4755401
Share on other sites

i really enjoy hicas . and really notice when it comes on . eg same piece of road at different speeds . also mint for turning on hicas test and your car sits there and every 2 seconds the rear wheels move full lock (1 degree ish) one way and then other way then back to normal as fast as they can . and every one says wtf is your car doing ? "its break dancing "

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4755416
Share on other sites

Has anyone ever had HICAS work in a straight line? That sort of issue, giving the car a 'flick'? Possibly due to the wheel not being on straight...?

only when the speedo cable snapped when i was on my way home from work, hicas started playing up along with the usual heavy steering. i was crab walking up a straight road, very strange feeling.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4755455
Share on other sites

only when the speedo cable snapped when i was on my way home from work, hicas started playing up along with the usual heavy steering. i was crab walking up a straight road, very strange feeling.

That's exactly what I had but without the heavy steering. :) Definite crab walk. Happens at higher speeds like 80km/h and you need to steer into it and if slow down quick a flick out of it. I recently had work done on the suspension but the steering wheel is not that straight after the alignment and wondered if that had anything to do with it...? Speedo cable is all good.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4755483
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi There I went through a rabbit hole of reading about Xenon headlights and the ADR regulations for having them installed. As people have been defected by running factory xenon I was researching in ways to make them compliant. Everyone always say needs to be self leveling and have washer installed, which I don't necessarily agree with. For this argument I'm using R34 as reference as I'm more aware on the construction of the headlight compared to the R33 Xenon, which may still be the exact same case.   For the self leveling clause taken from ADR 13 - Installation of Lighting and Light Signalling Devices on other than L-Group Vehicles As you can see the bold text "these manually adjustable devices from driver seats" are fine to use. As Series 1 Xenon model headlights do have a 4 level adjuster on the right near the ignition (however not series 2) then these model are consider compliant in that argument.   For the Self Cleaning aspect of this argument clause taken from ADR 13 - Installation of Lighting and Light Signalling Devices on other than L-Group Vehicles Now i can understand the argument that Xenon will need a washer as they are over 2000 lumens, but I clicked on the 12 at the end of that sentence and it takes me to the end notes which states R34 for headlight lenses are plastic, not sure if PL is mark as I don't currently have my skyline to confirm that marking is there. But could you not technically get a lenses with the PL marking on it and then get away with the argument that you need a washer. I went through a quick read of the adr and might have missed something else that may cause them to be non-complaint.    But wouldn't these technically be complaint headlights   Would love to hear other people input on this and shed some light   Edit In regard to the the washer portion I might be mistaken ADR 45 (which I believe is Regulation NO.45) states 12 cd (candela) I dont understand that portion in regarding to calculating the candela if anyone can shed some light. Otherwise I guess throw in a washer for the headlight and you definitely comply.
    • Took it to all Japan day, flogged the hell out of it and took it all, am a very very happy man  don’t know how that ended up in Greg’s thread before
    • Hey Nismo, any chance in the world you still have these seats?
    • I'd say closer to OG GTX3582R, just smaller trim - so 59mm inducer/82mm exducer as opposed to 62/82 for the first gen GTX3582R. Yeah EFRs were boss, the EFR8474 is still an absolute beast and it perplexes me that people still go to things like Turbosmart/Garrett etc when the results people are getting with those are pretty unremarkable compared to what you could get with a turbo available well before those options came out.  DriftSquid (I think) "upgraded" from an EFR9174 to a Turbosmart turbo and promised a comparison video - and kinda shuffled awkwardly and did a bit of diversion from the fact that they didn't get any improvement going to the currently massively hyped brand of turbo from a turbo that was a bit of a frankenstein that had been well superceded in it's own range before the Turbosmart unit he put on there even came out. I suspect the EFR would outperform most Xonas for what a lot of less-insane RB owners would go for, in the 400-600kw range but the Xonas are looking hard to beat up to maybe in the mid 700kw range at this stage- basically where EFRs don't really reach, and before the Precision turbos take over.  What the Xonas do well in the "EFR range" is be easier to package etc, and work very well if a divided housing doesn't suit your application.  
    • Are you sure the gasket is blown? What are the issues? Thermocure is the only flush I've seen do anything with rust, very impressed with that, Prestone, rust will be by the pool having a cigarette.  
×
×
  • Create New...