Jump to content
SAU Community

Recommended Posts

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Short answer: BAD...

Don't do it!!

BOV is there for a reason. To allow the pressurised air to NOT hit back onto the turbo compressor wheel. Over time it may cause damage to the fins.

Why on earth would you want the "flutter sound" anyway?? I hope it’s not to sound "cool" :banana:

Link to comment
https://www.sau.com.au/forums/topic/282464-flutterdumpdose/#findComment-4756251
Share on other sites

Lol, this topic again?

50% of the world will say its bad, the other 50% will say it isnt. Personally i think it sounds awesome, but at the same time i fully agree with Adam, i dont see how it cant be bad for the turbo. Its compressor surge, spinning the turbine backwards, it can not be good. If you didnt need a BOV, why would anyone have them?

Link to comment
https://www.sau.com.au/forums/topic/282464-flutterdumpdose/#findComment-4756421
Share on other sites

The sound of flutter/dose is awesome. Love it.

It will kill a ceramic turbo like stock R32, R33, R34, S13-S15 turbo's. Won't kill steel turbo's like single VG30 turbo's or RB30ET turbo's.

Flutter at 10psi is ok, but if you are running 14+ psi through a RB20/25 turbo it will kill the turbo

Link to comment
https://www.sau.com.au/forums/topic/282464-flutterdumpdose/#findComment-4757562
Share on other sites

The sound of flutter/dose is awesome. Love it.

It will kill a ceramic turbo like stock R32, R33, R34, S13-S15 turbo's. Won't kill steel turbo's like single VG30 turbo's or RB30ET turbo's.

Flutter at 10psi is ok, but if you are running 14+ psi through a RB20/25 turbo it will kill the turbo

+5MILLION

Dosing/flutter is THE BEST SOUND !!!

Link to comment
https://www.sau.com.au/forums/topic/282464-flutterdumpdose/#findComment-4758372
Share on other sites

THANK YOU!

farken hell...

I blocked off my BOV ages ago as it was leaking and I kept it like that as it sounds better then an atmo bov and is still legal...

Boost (on standard turbo (presumadely)) is now at 1 bar and it's been like that for a while... turbo still isn't dead.

Either way, overheating and general miscare of the turbo will destroy, fluttering can be a part of this but not a main part...

Link to comment
https://www.sau.com.au/forums/topic/282464-flutterdumpdose/#findComment-4758925
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Duh... to answer my own silly question, it's actually described in the FSM... ...400 pages away at the end of the manual, for RB25DE/DET signal descriptions, it cites the TPSwitch signal action, is dependent on the TPSensor value ~ this tends to infer the builtin POT voltage signal is the primary, and the switches are fallback/secondary should the POT fail/TPSensor signal lost (and switch alone with no TPSensor signal allows for base idle speed setting).... makes sense... they (TPS units) used to fail/wear the POT with time, they're not exactly built to last ~ having the switch as a redundancy gets around this...(or, it's less likely both signals would be lost as they're on different power rails)... and of course wrt RB26DETT, you have to electrically disconnect the IACV solenoid from the harness, to defeat idle air control...  
    • Dose is unaware just how much fun 145-150kw would be in a 2.5L NC MX5. It would be one of the most fun things to drive to ever grace SAU.
    • Same thought crossed my mind ~ depends on how one connotes 'stalling'...ie; gets a rough/stumbling idle as it get warm until it stalls... or... idles ok and simply falls-over when it gets to temp... ...you can test the whole circuit with a couple of resistors ...unplug coolant temp sensor, bridge terminals with a 2K7 resistor (ECU will do cold start), or with engine warm bridge with a 330R resistor (ECU will consider engine to be at normal operating temp)...it's a quick way to check wiring integrity/ECU response when you don't have a multimeter handy ...
    • They also make them with the motor mounted on the side 
    • Just be warned that that turbo will not be a direct re-fit to the car. The exhaust housing is, of course, in the same place. It has to be - it's bolted to the exhaust manifold. So the dump will fit up. But the centre housing is not as long, so the comp housing will move backwards. This will affect both the turbo inlet and the outlet. There is fab work that needs to be done. Yes. it has one, it should have one. Paper gasket.
×
×
  • Create New...