Jump to content
SAU Community

*work Meisters - If You Want Dish, These Are For U ! Epic*

dahandfull
 Share

Recommended Posts

dahandfull Proficient

dahandfull

Posted
Posted

Ok so i had planned a certain type of look that i wanted for my gtr, but over the last few months i have swayed for a different look due to the style of rebuild thats happening.

I bought these from jpn a few years ago and have sat in my shed eva since. You will need widebody kit for these as they hang out a fair way from factory r32 gtr guards. The tyres can be taken off and not be sent if thats what you want, or they will stay on for the sale. They arn't much good, prolly suit a few laps in a drifter as the are near/on the indicators. They are 265/35ZR18 dunlop lemanz

If i was to keep these, i would do a sticker replacement which you can easily buy from ebay or probably some business traders could get them and if i was feeling in the right mood, have a wheel shop pull them apart, re-polish the lip and paint re-paint the black spokes.

Specs are:

Work Meister S1 18x10 +18(F) 18x11 -8® 5x114.3

$2000

I am very open to swaps, interested in 18x9.5 to 18x10.5 advan, ssr, work, rays/volk anything jap realy.

Shipping will be on a courier, as this is much easier than aust post. Located on nth side of Brisbane, pick up is cool too.

Thanks

post-22000-1249781543_thumb.jpg

post-22000-1249781665_thumb.jpg

post-22000-1249781965_thumb.jpg

post-22000-1249782107_thumb.jpg

post-22000-1249782239_thumb.jpg

post-22000-1249782325_thumb.jpg

bean Apprentice

bean

Posted
Posted

hey dude, trade for race seat.

CORBEAU carbon/kevlar race seat, they are hand made and weigh 7kg.

i bought 2 of them for a different project but only used 1.

has been trimmed in black itilian leather with red stitching and has perforated center, it is brand new

cost me over $2500 to buy the seat and have it trimmed

sebastion Proficient

sebastion

Posted
Posted

these are cheap as guys, if I had the money they would be gone... and mike only sells top quality and what he says is the genuine truth... top bloke

cheers mate

Weezy Grand Master

Weezy

Posted
Posted

Only if these wern't staggered.. I have a set of DTM Rush wheels in Satin black 18" x 9.5" wide and +27 offset, since nice and flush with the guards. :(

dahandfull Proficient

dahandfull

Posted
  • Author
Posted
yes, these will fit a r32 perfectly. you may just have to roll your rear guards a little....

well they sit at least an inch outside of my gtr front and rear. so modification is a must, either widebody rear or some extreme flaring of the rear fenders

M I K E Mentor

M I K E

Posted
Posted
yes, these will fit a r32 perfectly. you may just have to roll your rear guards a little....

are you on drugs? 11-8 fits perfect on the rear of a 32? welcome to mexico :D

stupidly tough wheels, do you know if the fronts have much caliper clearance?

dahandfull Proficient

dahandfull

Posted
  • Author
Posted

M I K E I havn't had them on the front of my car, cause I just havn't had the chance to, but from experience id say you would prolly need a 10-15mm spacer...

lol - viva la mexico :D

dahandfull Proficient

dahandfull

Posted
  • Author
Posted

Hi All....

I just wanna point out that these will definately NOT fit standard R32-GTR guards. Im not 100% sure of R33/R34-GTR i would assume that they do not fit these either without some slight flaring (my opinion), and gtst would be a definate NO without a wide body.

Hope this can help answer some of you wonders.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
    • GTSBoy
      AC not coming from top vents

      By GTSBoy · Posted

      What HVAC actuator is under the steering wheel? Do you mean on the RHS of the centre console, immediately to the left of your shin? If so, then yes, it is probably that one, because that is the mode door actuator, and from what I know, it's still a pain in the arse to replace. I don't know about whole dash out, but you certainly have to rip into the centre console section. I don't know if it's covered in the workshop manual, as I haven't spent much time looking at those parts of it. (and by "the workshop manual, I mean the R32 GTR one, which is the most comprehensive one we have, and it should be similar enough between that and later cars to serve as a guide).
    • dbm7
      Shifting questions

      By dbm7 · Posted

      ...oops. forgot the TCU end...
    • Sleepergm
      Custom titanium intake

      By Sleepergm · Posted

      No I got mine from a friend that had fabricated one … but I had to fit it to my setup which was a hks turbo setup. His was a Garrett -7. So one of my turbos was not a flange for one side … then I had a leak in the welds I had to find a weld shut … in the end the setup was decent priced but I spent a lot to get it fitted. A couple companies I checked would make it but you’re talking 7-9k aud with titanium. No joke mine was 6-7k even second hand after I had to fit it in Hong Kong … labour is expensive here. 
    • Kinkstaah
      NC MX5

      By Kinkstaah · Posted

      I'd just like to restate that I don't think anyone here is actually hating I recently sold a car part to a guy who was building a forged auto R34, with MV stall and aiming at ~450kw. I told him that I'm him, from the future and to stop after it explodes once. I told him I knew he won't listen the first time, and that's fine. But if my predictions do come true - Change direction faster than I did. I also said it's probably no coincidence that the dyno plot of a reliable turbo engine starts to look a lot like a N/A motor. :p
×
×
  • Create New...