Jump to content
SAU Community

Recommended Posts

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

the tops had popped off? :P

Pretty much.

In this pic the one in the middle is good, the two on either side are dead:

DSC01452.jpg

Good coilpack:

DSC01455.jpg

Dead coilpack:

DSC01456.jpg

I lost three in one go that night.. had to get towed home as she barely made it up the tilt-tray tow truck.

if your plugs are 120,000kms old then that is definately the problem. even irridiums won't last that long and still perform well. just got and grab a set of copper plugs for about $4 each and throw them in. you will know straight away if it has solved the problem or not, and if it doesn't then you haven't wasted much money.

Coil packs 100000000000000000% it's been covered a million zillion billion times, R34's specifically have shit coils that ALWAYS die. A quick diagnostic with a paperclip will show error 21 from the ECU

Never replace with OEM coils as they will just shit themselves down the track. They can look shiny and new but the transistors inside suffer from wire seperation at engine temperature and gradually disable the coil pack even in fairly new cars (my last R34 did it when it was 3 years old....yes back in 2002)

Buy some splitfires, do not pass go, do not collect $200 and forget about the issue ever again :(

+1 x million

don't listen to them, get plugs first. they are ignoring the fact that you think your plugs are 120,000kms old, which even if you let iridium plugs run for their quoted life span of 100,000kms they are still 20,000kms overdue. and given that most iridium plugs don't last the full life of 100,000kms before playing up, it's pretty safe to say that it is your problem. i had iridiums worn out after 20,000kms in my gts-t.

now as cara said above, how can the plugs spark if the coil is playing up? well how can the spark plugs spark if they are playing up? if they are covered in carbon you will find that they will missfire. and to take a page out of your book cara, here is something copied from the NGK website

Carbon Fouling

Carbon fouling is the most common spark plug related failure, but is not a spark plug fault. Carbon deposits are conductive, and as they accumulate along the insulator nose they reduce the insulation resistance of the spark plug. As electricity always takes the path of least resistance a misfire may occur if a significant amount of carbon deposits accumulate. A spark will not form as electricity can track along the conductive carbon deposits to the metal shell (as shown in red below) rather than forming a spark across the electrode gap which has a very high resistance.

sparkplug_tech_103.jpg

now the carbon deposits could be caused by many things. in this case though i would most likely say that they are caused simply because the plug is worn and isn't able to ignite all the fuel. as the plugs wear the gap gets slightly bigger until a point where, no matter good your coils are, the spark isn't able to arc accross the now larger gap and finds an easier route to take.

and since plugs are much cheaper than coils, it is very much worthwhile doing them first. and since you think they are 120,000kms old then even with new coils they wouldn't last much longer anyway.

i should add that i am not saying that there isn't a chance it is the coils, just saying that i sure as hell wouldn't be buying new coils because a set of really old plugs are causing a missfire without trying the option that is more than likely the issue and costs quite a few hundred dollars less and will more than likely need to be done even with new coils anyway.

Plugs don't cause the check engine light to come on, he will have error 21 logged in the ECU, every R34 loses it's coil packs....it's an accepted fact, much like the sky is blue.

Just trying to save him dicking around with plugs when we alll know it's the coils. I've run copper plugs under silly boost for 40,000kms and still never even got close to losing a cylinder like when a pack shits itself

don't listen to them, get plugs first. they are ignoring the fact that you think your plugs are 120,000kms old, which even if you let iridium plugs run for their quoted life span of 100,000kms they are still 20,000kms overdue. and given that most iridium plugs don't last the full life of 100,000kms before playing up, it's pretty safe to say that it is your problem. i had iridiums worn out after 20,000kms in my gts-t.

now as cara said above, how can the plugs spark if the coil is playing up? well how can the spark plugs spark if they are playing up? if they are covered in carbon you will find that they will missfire. and to take a page out of your book cara, here is something copied from the NGK website

now the carbon deposits could be caused by many things. in this case though i would most likely say that they are caused simply because the plug is worn and isn't able to ignite all the fuel. as the plugs wear the gap gets slightly bigger until a point where, no matter good your coils are, the spark isn't able to arc accross the now larger gap and finds an easier route to take.

and since plugs are much cheaper than coils, it is very much worthwhile doing them first. and since you think they are 120,000kms old then even with new coils they wouldn't last much longer anyway.

i should add that i am not saying that there isn't a chance it is the coils, just saying that i sure as hell wouldn't be buying new coils because a set of really old plugs are causing a missfire without trying the option that is more than likely the issue and costs quite a few hundred dollars less and will more than likely need to be done even with new coils anyway.

Plugs don't cause the check engine light to come on, he will have error 21 logged in the ECU, every R34 loses it's coil packs....it's an accepted fact, much like the sky is blue.

Just trying to save him dicking around with plugs when we alll know it's the coils. I've run copper plugs under silly boost for 40,000kms and still never even got close to losing a cylinder like when a pack shits itself

my engine light came on when all 3 of my coilpacks busted.......

and mad082, thanks for the info.

Plugs don't cause the check engine light to come on, he will have error 21 logged in the ECU, every R34 loses it's coil packs....it's an accepted fact, much like the sky is blue.

Just trying to save him dicking around with plugs when we alll know it's the coils. I've run copper plugs under silly boost for 40,000kms and still never even got close to losing a cylinder like when a pack shits itself

actually, according to my tuner, a problem with any part of the primary ignition system, including spark plugs, could cause that error code to come on,,,,

either way, my new plugs have been ordered and ill try that first, another interresting fact is that if it was one or two bad coils i would expect to have had one or two totaly ruined spark plugs, however all my spark plugs looked exactly the same

if i still have the problem then all i have to do is take the intake back off and chuck some new coils in

What is your oil consumption?

I had the same problem as you described. I also burnt 5L of 40w-70 oil only driving 500km so keep checking your dipstick to see how your oil is going. (i doubt it will be this bad as the person that owned the skyline before me killed the engine). Especialy if you have black spark plugs, its the number one sign of them burning oil and although your engine is young mine was dead at 150,000km so theres a chance its a internal problem.

i use the same oil as ndawg, 10w60 castrol edge full synthetic for the last 3-4 oil changes, but i never have to top up btw 5000km intervals, infact the last time i went to change my oil after 5000km it was still relitively nice and brown considering it just did 5000km, so i added a wee bit to top it up and then let it do another couple of thousand kms before i changed it,

and even with this engine issue, my oil consumption hasnt changed noticably

Allen key

socket set

i think that's it.

Take off the intake, inc pipe up to the throttle body then allen key take off the coilpack cover (Nissan 2500 plate) then socket takes off blots for coilpacks, pull the coilpack out then socket take out the plugs.

Do one at a time!

Bed time for me now...

Ok well I came around to checking out my plugs today...any ideas on how I take of the piping for the throttle body hahaha, I unscrewed the coilpack cover and could barely see under becuase the piping wouldnt let me lol...I sat there looking at it blankly to see how I can take it off haha but no luck on what i was doing :)

Ok well I came around to checking out my plugs today...any ideas on how I take of the piping for the throttle body hahaha, I unscrewed the coilpack cover and could barely see under becuase the piping wouldnt let me lol...I sat there looking at it blankly to see how I can take it off haha but no luck on what i was doing :)

mine wasnt too hard, just had to get up the nerve to start pulling hoses off, was about 10 hoses and 5 electrical connections,,,,good idea to take a picture first!

actually, according to my tuner, a problem with any part of the primary ignition system, including spark plugs, could cause that error code to come on,,,,

either way, my new plugs have been ordered and ill try that first, another interresting fact is that if it was one or two bad coils i would expect to have had one or two totaly ruined spark plugs, however all my spark plugs looked exactly the same

if i still have the problem then all i have to do is take the intake back off and chuck some new coils in

Unfortunately you're tuner isn't as familiar with the R34 electrical system as me, I've owned R34's for over 7 years and know the electrical/ECU systems backwards.

The CEL for error 21 is only triggered once the expected current drain isn't seen by the ECU, this can only occur when the firing transistor doesn't activate (as it's f**ked) leading to a dwell current that doesn't drop. A spark plug, fouled, missing, shorted etc etc can't replicate this event and will NEVER show the CEL

Your tuner should have pulled the codes and seen it was a 'non-consecutive firing signal detected' he should also know that every R34 under the sun has this issue at some point.

My advice is do both the plugs and the coils as you'll just save time and frustration of fitting new plugs, finding it starts playing up a week down the track. Then you have to order some coil packs and then put them in risking damage to nice delicate gaskets on the intake that have to keep coming on and off.

mine wasnt too hard, just had to get up the nerve to start pulling hoses off, was about 10 hoses and 5 electrical connections,,,,good idea to take a picture first!

Sounds like a bit of a mission lol, not what was coming to my head...from what i saw there was some nuts/bolts involved haha...would there be a significant difference between the 33 and 34?

Yep that's why I still didn't trust the updates that were meant to elliminate the coil frying, for the sake of installing 6 zener diodes for <$3 it's definately good insurance.

Pretty much.

In this pic the one in the middle is good, the two on either side are dead:

DSC01452.jpg

Good coilpack:

DSC01455.jpg

Dead coilpack:

DSC01456.jpg

I lost three in one go that night.. had to get towed home as she barely made it up the tilt-tray tow truck.

they could die a simple death (without any sign) or a fatal one (like NDAWGS) and start smoking up & clearly its melted at the tops.

does it always happen or is it intermittent?

The e-manage killed Nates packs, the e-manage sends a constant voltage to the coil packs AND ignition pulses. So as the voltage drops between pulses (but not to zero as it should) the current starts to increase to maintain the wattage, this burns out the packs explosively. It's the same problem with RX-8's and S15's...or any internal transistor coil-pack really.

Sounds like a bit of a mission lol, not what was coming to my head...from what i saw there was some nuts/bolts involved haha...would there be a significant difference between the 33 and 34?

The r34 engine is rb25de NEO

Its a completely different way in taking off the plugs, they dont have to worry about a intake pipe sitting on top everything.

1) Take the airbox out or pod filter.

2) Take off the Air flow meter and put it away somewhere so it cant be damaged.

3) There should be a hose clap that is clamping the intake pipe around the throttle body, that comes of with a philips head and it loosens the pipe so it can be pulled off the throttle body. There are also a few blots i think that keep the pipe stable so undo those to pull it out.

4) Allen key unscrews 8 screws (by memory) that allow you to take the cover off and it will reveal 6 coilpacks

5) socket set takes the blots off each coilpack then they simply come out by pulling on coilpack as they have rubber seals

6) socket takes spark plug out

7) if sparkplug us fouled get some dielectric grease to clean them (found at all car shops, supercheap ETC ETC)

8) repeat step 5-7 making sure you do 1 cylinder at a time to save you the mess.

AYW550 - if your car only burns a few drops and your using 10w-60 then its where it should be in life. Its just a sligltly thicker oil than the 10w-40 to compensate for inevitable engine wear. If the plugs have never been changed, then they have had 120,000km of oil burn on them :D ....... seriously try those new plugs. If it was the coils your going to need new plugs anyway so just try the plugs first that way if it isn't them you have the plugs already there waiting for new coils if it ends up being coils.

The r34 engine is rb25de NEO

Its a completely different way in taking off the plugs, they dont have to worry about a intake pipe sitting on top everything.

1) Take the airbox out or pod filter.

2) Take off the Air flow meter and put it away somewhere so it cant be damaged.

3) There should be a hose clap that is clamping the intake pipe around the throttle body, that comes of with a philips head and it loosens the pipe so it can be pulled off the throttle body. There are also a few blots i think that keep the pipe stable so undo those to pull it out.

4) Allen key unscrews 8 screws (by memory) that allow you to take the cover off and it will reveal 6 coilpacks

5) socket set takes the blots off each coilpack then they simply come out by pulling on coilpack as they have rubber seals

6) socket takes spark plug out

7) if sparkplug us fouled get some dielectric grease to clean them (found at all car shops, supercheap ETC ETC)

8) repeat step 5-7 making sure you do 1 cylinder at a time to save you the mess.

AYW550 - if your car only burns a few drops and your using 10w-60 then its where it should be in life. Its just a sligltly thicker oil than the 10w-40 to compensate for inevitable engine wear. If the plugs have never been changed, then they have had 120,000km of oil burn on them :) ....... seriously try those new plugs. If it was the coils your going to need new plugs anyway so just try the plugs first that way if it isn't them you have the plugs already there waiting for new coils if it ends up being coils.

deffinately, thanks for the support

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • No it's fine. Heat sleeve is a thing. With oil running through it it is unlikely. Engine off heat soak can be a thing though. There is no way that you have a leak through the hose. That has pressure behind it and any small hole will turn into a large one in very short order. It is so much more likely to be leaking from the connection.
    • Really? That's piss weak. I didn't know they hobbled the shitboxen that badly. OK. So probs need to buy a flywheel too. But that's not too bad.
    • Hi all. I already posted some newbie-ish questions here and there but this will be my first "big" post. Last summer I went and fulfilled a kind of childhood wish, because I just thought I needed this experience in my life no matter what. The car I bought is a mildly modded 1995 BCNR33 Vspec. It was repainted to a metallic orange color all around and it had all windows reseated. Not so well done black respray in the trunk and a metallic black in the engine bay. From outside it looks very nice except for a minor paint error on the roof and the rear spats needing new adhesive tape. The inside is pretty clean and no broken plastics, missing or faded buttons. Even the adjustable mirrors and trunk antenna work like a charm. Despite a moderately long list of issues I don't (yet) regret buying this car. Most mechanical problems are just due to age, like worn rubbers here and there. The underside sadly has lots of corrosion, especially to the back. It looks like it either has been driven in the winter for a while or it lived near the saltwater in Japan, the rust is nothing terrible but it'll require to be looked after. Mostly panel gaps and all the mounted components underneath are a bit crusty, but I don't think anywhere has progressed so badly that there's going to be holes. Front right jacking rail is crushed and needs some care so it doesn't develop into a rust crater at some point. Worst part is definitely the strut towers. I thought they looked fine but after taking off the strut bar I noticed that it actually started bulging up on the passenger side. Probably would have passed on the car or negotiated down by some thousand Euros more if I had noticed this before buying, but here we are. Trunk area also has signs that there was a water leak to the interior once but nothing too crazy, I guess lots of Skylines had this at some point. As for the list of (known) issues, I'll try to make this compact. I hope the coloring is self explanatory. Mechanical: -Various busted or soon-to-be busted rubber bushings and ball joints. Will replace ball joints with OEM or better and bushings with polyurethane where possible. -Shaking steering wheel at above 80kph -downshift from 5th to 4th is a bit crunchy unless I rev-match, might just try to renew the shifter assembly, but it's not a priority issue -tailshaft centre bearing could use a replacement, is it worth going 1-piece tailshaft as it doesn't look too fresh all around? Chassis: -underbody corrosion on many spots and in hollow spaces, needs to be treated -corrosion on many bolts, hoses, lines, suspension components, subframes, will be treated when replacing of the bushings is needed as time goes on -strut tower top panels and some of the surrounding panels are rusty, so needs fixing. Will look into doing this with a buddy in the winter, otherwise bite the bullet and pay a professional -driver side door is misaligned to the body and needs to go a slight bit more inwards -both door windows are misaligned and have an airgap where the window meets the door at the B pillar -The Aerocatch latches for the bonnet have locks but no keys, need new keys. -driver side door window is kind of gritty and could use a polish -damaged jacking rails and front frame rails, from people lifting the car the wrong way, might have this fixed by a bodyshop Electrical: -Nismo tachometer is just bouncing and displaying nonsense, supposedly worked fine when the stock ECU was still in the car -An old Greddy boost controller sits on the dash which will be removed as it servers no purpose anymore. -a led segment rpm gauge is on the steering column, will probably also be (re-)moved once the Nismo tacho is working correctly -there was an attempt to make the sound system better by the previous owner but it was just inducing noise all the time, ripped out the amp and filters in the back, no music for now -trunk antenna goes up as long as the radio is on regardless of the mode, I want it to only rise if I choose Radio specifically or per switch -3rd brake light is a bit dimmer than the taillights but everything was converted to LEDs so mabye now it just seems dimmer? -reverse light flickers, have to test if that behavior changes when I fiddle with the gear stick. Hope I can get around changing the switch. -Left side taillight, blinker section has minor water intake and is humid after washing. Other side has a hole in it, probably for that exact reason. I'll probably reseal them entirely and plug the holes. Engine: -minor coolant drips on one or the other hose -rear turbo leaks oil onto the exhaust making the car essentially undriveable due to fire hazard -Oil filter relocation kit has an oil drip at the Dash lines, will probably make a new connection there and tighten real good and pray -throttle body assembly is slightly stuck for the first throttle pedal input after sitting for a while I'm always open to suggestions and advice from more experienced people, I'm sure half of this list is easily dealt with and just requires some time and effort to sort out properly. Once I have some proper pictures of the car I will post some in this thread, I just have to remember to take some more once I get the chance to. Will post updates when I have news on anything, I want to try to keep this thread as kind of a logbook as well. Ultimately my goal for this car is to just enjoy it. An engine rebuild is probably going to happen sometime as well, because it is old after all. It will never be fully new again, I am just not that rich. But I want it to look good, work well and not rot away while I drive it. I'm probably gonna spend a lot of money on this journey, hopefully not an unreasonable amount.
    • Hi all. So one of my major issues at the moment is my rear turbo leaking oil on the exhaust (and the general area). I presumed it was the rock hard super old drain hose, which it was not. So now I am in the midst of removing the rear turbo to get access to the banjo bolt that goes into the turbo oil feed. As one of the previous owners accidentally? tore off the OEM oil feed hardline that reaches behind the turbo, they ran braided lines directly to the turbo, presumably PTFE. Now, regardless if the line has rubber or teflon inside, is it just generally a bad idea to do this? I imagine these lines get quite hot being between the engine, turbo core and exhaust manifold. I suppose it's not too far fetched to think the line may even have melted. I'd love to hear your opinions on this as as the replacement OEM hardline piece is 130 per unit. And cutting open the currently mounted line to see inside will mean I just have to get a replacement either way. So far I am hoping maybe the bolt just loosened or (god forbid) they forgot one of the crush washers.
    • If it's a factory 20de manual probably has the 6 bolt flywheel in which case the det clutches won't work as they're 9 bolt.
×
×
  • Create New...