Jump to content
SAU Community

Electrical Issue: Drop In Voltage On Startup


rawd
 Share

Recommended Posts

hi all,

have an issue that has been pissing me off ever since i bought the car - hope there's someone out there that might have an idea of how to fix it cos i can't afford to see an auto-elec right now.

on start-up when i go to reds, sometimes it will go straight to 12v and crank first go (most of the time needs a bit of gas but i think that's cos my car is running rich)

other times when i go to reds, voltage will drop < 10, lights dim, fuel pump will struggle to prime and starter motor struggles with clicking noise and i have to get on the gas or keep turning it over to get it started. usually if i keep trying to turn it over a few times with the key the volts will eventually rise back to around 12 and it will start. each time i turn the key i hear a single click - not sure what this sound could be but it strangely sounds like its coming from the door.

alternator is pretty new - charges at 14.2 when running. battery has been tested by the place i bought it and it's fine. could be my alarm and the clicking sound is the keyless entry? bad ground somewhere? battery is actually screwed? i have no idea but would like some ideas on how to diagnose so i can either take to auto elec for a quick fix or fix it myself.

thanks in advance.

rod

Link to comment
Share on other sites

more info: voltage drop doesn't just happen on start-up. sometimes when i get out of the car and press the keyless entry the car won't even have enough volts to lock all the doors. i usually have to either keep trying or put the key in the ignition and crank to bring the volts back up.

shit - i know this could be one of a million things but i appreciate any input

Link to comment
Share on other sites

To me it still sounds like a battery issue, even if a battery shows 12V on a multimeter doesn't mean it is a good battery, does it give you the most problems in the morning? because that is when batteries are at their lowest, try to jump start the car off another car to see how it goes. If the problem is still there, I would be looking at the starter circuit and would suspect excessive current draw somewhere there. Sometimes starter motor solonoids get sticky and don't always throw (causing a clicking noise).

Before anything else I would be looking at the battery. The average battery should be change every 2 - 3 years and the number one cause for car starting problems is battery power. What size is the battery? check the Cold Cranking Amps (CCA) on the label. The higher the better. Check the battery voltage with engine off, a good battery should read about 13.8V and watch the multimeter while starting the car to see what it drops down to.

As for the alarm it sounds like it is struggling to get power, now alarms either have power or they don't, if it is struggling to lock the doors then this leads me back to battery power or lack of power. It wont be a bad investment if you bought a new battery because this will benefit all electrical components in you car from ecu to sound system (especially if running subwoofer/s).

Based on what you have said these are my thoughts from my experience.

Link to comment
Share on other sites

To me it still sounds like a battery issue, even if a battery shows 12V on a multimeter doesn't mean it is a good battery, does it give you the most problems in the morning? because that is when batteries are at their lowest, try to jump start the car off another car to see how it goes. If the problem is still there, I would be looking at the starter circuit and would suspect excessive current draw somewhere there. Sometimes starter motor solonoids get sticky and don't always throw (causing a clicking noise).

Before anything else I would be looking at the battery. The average battery should be change every 2 - 3 years and the number one cause for car starting problems is battery power. What size is the battery? check the Cold Cranking Amps (CCA) on the label. The higher the better. Check the battery voltage with engine off, a good battery should read about 13.8V and watch the multimeter while starting the car to see what it drops down to.

As for the alarm it sounds like it is struggling to get power, now alarms either have power or they don't, if it is struggling to lock the doors then this leads me back to battery power or lack of power. It wont be a bad investment if you bought a new battery because this will benefit all electrical components in you car from ecu to sound system (especially if running subwoofer/s).

Based on what you have said these are my thoughts from my experience.

agree with above, check the battery current holding ? bet its rooted

it will show 12v but wont start the car for crap, also check the grounds and positive terminals, remove them, clean with battery cleaner wire brush thingy. try it again. also voltage at the alternator doesnt mean the current is getting to the battery, just replaced one on a R31 last week, same issues, new battery ... stuffed alternator but showing 12-14 volts running

the alarm will get flaky as hell if it sees low voltage, doors will do weird things, siren on and off, etc,,,,plus the battery backup in the siren will die too if its not fixed soon...

Link to comment
Share on other sites

awesome. thanks fellas, this is exactly what i needed to start my mission.

actually the battery is quite new (3-4 months maybe) and it still has warranty so i'll get them to check it out for me.

when i watch my volt gauge during start-up i can see it drop to 10, sometimes 8 so it definitely could be that. it never sees above 12 when the engine is off.

i will try cleaning the contacts as well cos i've never actually done that.

alarm is old and shit. siren doesn't go off ever but the pager does so that's why i've kept it.

thanks again all.

Link to comment
Share on other sites

battery shouldnt drop below 10V on cranking

is it a sealed battery (maintenance free)... or has it got the cells you can top up?

you might wanna load test the battery...thats your best bet.

maybe run it past an auto elec and have a chat to them, usually they are nice enough to do a free quick battery check...

cos if its rooted, chances are you'll buy a battery off them so its in their intrests to help you out

Link to comment
Share on other sites

battery shouldnt drop below 10V on cranking

is it a sealed battery (maintenance free)... or has it got the cells you can top up?

you might wanna load test the battery...thats your best bet.

maybe run it past an auto elec and have a chat to them, usually they are nice enough to do a free quick battery check...

cos if its rooted, chances are you'll buy a battery off them so its in their intrests to help you out

hey sloupos, yeah pretty sure i can pop off the caps and top them up. going to check out a few places tomorrow. thanks mate.

Link to comment
Share on other sites

i just spoke to a friend that had a similar problem - only low volts when the engine was not running - and he said that it could be a starter motor issue. is this logical?

at rest the battery should be 12-13 volts roughly

when you turn it over the thing will drop to 10ish if the starter is getting ready for a clean up. drawing too much current, or motor mistuned

skyline starters rarely fail, you can pull them off and clean the goop out of them, take off the end cap and shine the rotor(communicator- bronze shaft)

and clean off the laminated coils, slap it back in for another 5 years. worse case , put in new brushes. but rare

yes, new batterys do fail, my Odessy PCA 1200 failed the first week of having it, DEAD cell, wouldnt charge above 10volts

you should use some of this stuff if your battery isnt sealed, works a treat , just hard to find...lol BIG W had it I think for about 7 bucks

access_inox_inoxBC.jpg

Link to comment
Share on other sites

quick update - cleaned and tightened all ground contacts i could find around the car

battery is now sitting between 12-13v on standstill which hasn't happened since i've owned the car

starter motor still doesn't turn over first time/every time, but it's definitely doesn't f**k up as much.

thanks again for your help folks. saved me a lot of money i don't have.

Link to comment
Share on other sites

I have a quiet chirp from my alarm siren every time I turn the car ignition on, the siren also has the same noise when I select the silent arm/disarm option from the remote. I thought this was caused by a voltage drop, I have heard this on other cars but installers advise some cars do this and some dont, unknown why? The alarm and car dont miss a beat so not a big problem but if there is a way to fix I would like to do, any ideas appreciated....

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Hey Matt, Link pointed to the 2x IGN power sources from the car as a likely issue, and sure enough pin 31 in the loom does not have power when IGN is on (24 does). So at the ECU, (and this is probably the case for R32 as well as C34) most of the ECU loom goes through the firewall behind the blower motor and there are 2 plugs (of 3 in the junction box) which go up and under the dash, the third plug heads under the carpet to places unknown (likely a body to dash loom joint) So, I started to follow that problem through yesterday. Like Johnny (and R32) I assumed that power was supplied through the 2 connectors near the left headlight so I spent some time pulling the intake etc off and cleaning of 400,000klm of dirt and oil leaks and checking those pins, but there was nothing related to the engine parts or ignition fuses there (and no purple with white trace wire in either side of the connectors) Given that the wire didn't seem to go via the engine bay, I then checked there is continuity from Pin 31 to the second connector to confirm no wiring issue in the ECU loom (it looked likely, given how much that has been hacked up over the years!). The pin marked with the purple dot is the other end of the wire to Pin 31 Then I check for IGN power in the dash loom side of that connector with the key on. Nothing. Given that loom goes up and underneath the top of the dash there is no tracing it without taking the dash out, so I went to the driver's side to see if I can find the other end of that (I'm expecting to get to big body junction boxes after I pull enough apart). However, to get to those functions, I had to pull the covers off the drivers side, I'm pretty sure the problem is in this pic Yep, factory remote start (bottom right), local immobiliser (middle) surrounded by 20 years of butchery. Plan is to totally remove the remote start and immobiliser (I think I will lose remote central locking temporarily as a result) to remove all the suspect stuff given I have other more modern security in the car It's gonna take a while, and it is both cold and uncomfortable out in the shed, not looking forward to it.
    • Hey team,  The clutch on my newly bought 25 swapped r32 feels average and sticks half way. Went to go order a new clutch master but it does not look like the ones that suit the one that’s in the car…    does anyone know what clutch master is this just by looking ?  (The feed is on the side rather than the bottom like the ones the pop up online)  thanks guys new to the RB scene so any help is appreciated cheers !!
    • Id be more than happy to sign up!!! Where do I send the invoices for my fuel usage? I'm happy to provide the mower, oil, and the labour to abuse the motor, just a little help on fuel would be great...   I had tipped the container of oil out into my big "drip tray" and left the small container upside down to drain the oil out of itself overnight. PIcked the container up today, and it has a layer of what feels like either dirt, or shit tonnes of carbon in the bottom of the container. I'm leaning towards it likely being dust, as I doubt the quality of the Sunli BumbleBee having a decent air filter on it, and sections of my yard produce a dust storm, especially because of the high lift blade!   So, filled her up with some fresh Nulon. Seemed to run fine, but it seems to want to run at really high RPM (higher than normal) even with the governor spring slacked off after fire up to try reduce it. If I back the throttle off it a bit to drop the rpm to where I'd like it to be when mowing light grass, it starts to blow a bit of smoke out the exhaust. Opening the throttle back up clears that out. It's definitely breathing oil, as I put my hand down at the breather hose and it's spitting some oil.   My guess is it having been running at high rpm, oil never changed, and it eating dust has destroyed the rings. You know what that means? Time to send it!!!
    • That is what will seal with the bonnet closed. Follow it down while closing the bonnet to see where it ends up with the bonnet closed. The panels don't do anything other than spending money, which this one will do just fine. :p
    • Nah just send me a photo or a drawing and I'll tell you which is better.  It's a new SAU service.
×
×
  • Create New...