Jump to content
SAU Community

Injector Resistor Pack For 1000hp Rb26?

R31 Gagz

By R31 Gagz,
in Engines & Forced Induction

 Share

Recommended Posts

R31 Gagz Collaborator

R31 Gagz

Posted
Posted

Hi Everyone,

Mate of mine has built a 1000hp rb26dett and is in the process of installing it into his r32 gts...currently he is nutting out the loom and electrical side of things and wanted to know if he needed to run the factory resistor pack for the injectors? Not sure what injectors he is running, obviously something big enough to support 1000hp :P...if its important I will ask him and post it up.

Thanks to anyone that can help. :ninja:

Cheers!

Craig

Link to comment
Share on other sites
GTRNUR Grand Master

GTRNUR

Posted
Posted

Depends entirely on the ECU he is using and the type of injector drivers that ecu has.

Ecu's that can drive low impedance injectors without a resistor pack can potentially run lower pulse widths as the injector driving current is controlled more precicely. Most if not all big injectors are low impedance and would require a resistor pack if your using a power fc or something simular.

Link to comment
Share on other sites
R31 Gagz Collaborator

R31 Gagz

Posted
  • Author
Posted
Depends entirely on the ECU he is using and the type of injector drivers that ecu has.

Ecu's that can drive low impedance injectors without a resistor pack can potentially run lower pulse widths as the injector driving current is controlled more precicely. Most if not all big injectors are low impedance and would require a resistor pack if your using a power fc or something simular.

Hi GTRNUR,

He is using a Link Plus G3 ECU to run Siemens Deka 850cc injectors, here's an excerpt from the ECU manual on injector drives:

The LinkPlusG3 has eight independant injector drives allowing sequential, sequential staged, group and group staged fuel injectors.
These injection drives are designed to be used with high impedance injectors, injector ballast resistors must be wired if low impedance injectors are to be used.

So I guess he just needs to find out if the Siemens injectors he is running are low or high impedance, if they are low then use the factory resistor pack?

Cheers!

Craig

Link to comment
Share on other sites
  • 2 weeks later...
R31 Gagz Collaborator

R31 Gagz

Posted
  • Author
Posted

Turns out my mate wants to try and accomplish this a bit cheaper and make the resistor pack himself, does anyone know what resistors he will need and how many? (one per injector maybe?)

He's found a place in the US that sells the factory resistor packs for about $180 (not sure if AU$ or US$), does anyone have good condition one for sale that he might go instead? Otherwise I think he'll try and go the above mentioned route to save some $.

Cheers!

Craig

Link to comment
Share on other sites
discopotato03 Grand Master

discopotato03

Posted
Posted

Not directly related but I was speaking to Ray Hall this morning about ViPec V44's and peak and hold injector drivers .

ViPec market a peak and hold driver box for the V44 because it comes with low current high impedance injector drivers .

I'm not sure if Link do them and the real question is whats cheapest , large high impedance injectors or peak and hold ones with the driver box .

A .

Link to comment
Share on other sites
grandmasterb Grand Master

grandmasterb

Posted
Posted
Turns out my mate wants to try and accomplish this a bit cheaper and make the resistor pack himself, does anyone know what resistors he will need and how many? (one per injector maybe?)

He's found a place in the US that sells the factory resistor packs for about $180 (not sure if AU$ or US$), does anyone have good condition one for sale that he might go instead? Otherwise I think he'll try and go the above mentioned route to save some $.

Cheers!

Craig

They can be sourced new from Nissan or plenty of second hand ones or he can get one from a wrecker out of a MR30 (exactly the same as the gtr ones) or make up his own.

I used a gtr resistor pack the first time and made up my own the second time (purchased the 10ohm resistors from Jaycar) the ones you are after are the LARGE 10W/10ohm resistors and roughly $2 each :D

Link to comment
Share on other sites
dano4127 Veteran

dano4127

Posted
Posted
Turns out my mate wants to try and accomplish this a bit cheaper and make the resistor pack himself, does anyone know what resistors he will need and how many? (one per injector maybe?)

He's found a place in the US that sells the factory resistor packs for about $180 (not sure if AU$ or US$), does anyone have good condition one for sale that he might go instead? Otherwise I think he'll try and go the above mentioned route to save some $.

Cheers!

Craig

Hey Mate

I purchased a 6 ballast resistor pack for NZ$105 from NZEFI: http://www.nzefi.com/

I think Link themselves sell them for around that price too whick would work out to around AU$85+ Shipping

Probably just as easy to get the Vipec one as they should be around the same price

Good luck

Dan

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Nightmare_mistress_R33
      CD009 RB Conversion

      By Nightmare_mistress_R33 · Posted

      I am currently going this route. I am curious how much horse power you put behind the cut bell housing? Collins was telling me I am going to crack it and bluh bluh bluh. Because I didn’t buy the custom fly wheel from him. I am looking for somewhere around like 500 hp
    • Beanie
      Hello from the UK

      By Beanie · Posted

      Forgot to mention that these are the before pics when I first got it!
    • Beanie
      Hello from the UK

      By Beanie · Posted

      Thanks @PranK for the updated member status, much appreciated! 👍🏼 Now, about those pics… Unfortunately I could only find ones that I took in the dark. I was soon to discover that underneath it wasn’t in the best shape, but it was mine and that’s all I cared about at the time 😆
    • r32-25t
      PRP RB26 cast block + head prototype running

      By r32-25t · Posted

      Buy one
    • GTSBoy
      A little PU bush story

      By GTSBoy · Posted

      Oh, and only having done this task yesterday, I've now driven the car ~60km since, and while it is hard to avoid placebo effect and confirmation bias, I reckon that some annoyances I had with the way the car has been behaving have improved. Which....kinda makes sense, I guess. If the bushes were really stiff and resisting rotation, they would have been contributing to the effective wheel rate. And if it was more so on one side (which it was, because one side was worse than the other) then.... you might imagine that the additional rate would be asymmetric, and potentially even different between compression and rebound. And so... the car has been twitchy at higher speeds - like freeway on ramps. It really shouldn't be. The wheel alignment is good and there are no (other) known problems elsewhere in the suspension. But at 90-100 on a long sweeping ramp, tiny steering wheel motions would make it feel like it wanted to rear steer. Quite nervous. At lower speeds it would heave about in a manner that it didn't use to. Didn't want to put power down, etc etc. Now...seems to behave better. Am going to have to concentrate on the various corners where it has exhibited weirdness, on the rare occasions when I can get a decent run at them without Methanial getting in the way in his D-Max/Ranger/LDV Van/etc.
×
×
  • Create New...