Jump to content
SAU Community

Recommended Posts

Engine

Forged Pistons

Forged Rods

Performance rings

Balanced and blue printed block

Ported head

Billet crank

Kevlar timing belt

Tensioned valve springs

550cc injectors

HKS Cams

HKS Cam gears

HKS Silicon hoses

HKS Duel dump pipe

HKS 3 layer head gasket

HKS POD filter

GFB BOV

Engine resprayed candy apple red

Intake

Upgraded roller bearing turbo

Z32 AFM

R33 radiator

Big cooler

Thermo fans

Stainless induction

Powder coated black cooler pipes

Driveline

OS Giken custom clutch

Lightened fly wheel

2 way mechanical LSD (Cusco I think)

Fully adjustable JIC Gold coilovers

Exhaust

Blitz NUR-Spec 3" stainless exhaust

Interior gadgets

HKS incab duel stage boost control

HKS Turbo timer

HKS Boost gauge

HKS Stainless shifter

Momo steering wheel

Recaro adjustable back race seat

HUD (speedo on windscreen)

Black wired alarm

Keyless entry

Electric windows

Full stereo including sub and amp

Origional 180sx floor mats

ECU

Dr Drift tuned ECU

Suspension etc

Strut brace

Nolathane bushes etc

P1 Buddy light weight race rims

Upgraded cross drilled disks

Upgraded callipers

Project Nu race pads

Body

Car resprayed Polar White

C-West front bar

Buddy club side skirts (I think)

Vertex rear bar (I think)

Shaved rear wing

Type x tail light and centre

I've just paid a years rego.

If you'd like any info just ask.

I'm looking for $13,000

Will neg for serious buyer

The car puts out close to 250rwkw on an aggresive tune, I drive it around at 170rwkw because it's just used to get me too and from work.

n586867363_1826830_4443285.jpg

4435_85669702363_586867363_1826822_2892650_n.jpg

Link to comment
https://www.sau.com.au/forums/topic/283331-180sx/
Share on other sites

  • 2 weeks later...

G'day mate, it's an 89 model so it's a ca18, great on fuel and massive amounts of torque, it's above 600nm on a high tune.

I dont have reciepts for the work unfortunately due to a horrible house move where i ended up living in a shed for 4 weeks!

The turbo is a modified Garret roller bearing turbo, I'm only running 12psi as it's only used as a daily driver, it sure makes some noise when it's boosting!

Im located in Ballarat Victoria, about an hour from Melbourne.

Link to comment
https://www.sau.com.au/forums/topic/283331-180sx/#findComment-4791155
Share on other sites

  • 2 weeks later...
  • 1 month later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Dunno what to tell you, when I look at it on Consult I can see this warmup timing map kicking in around 40C coolant temp and it sticks around for a while:  At part throttle on the normal base timing map it peaks around ~43 degrees of timing or something like that, this warmup timing map drops it to like 12-15 degrees. 
    • I don't think that's what you're seeing. Something else doing that. The only time I've seen it get so retarded is when it's trying to control idle (in which case we're not talking about mapped timing tagets anyway) and when there is an extreme coolant temperature sensor fault. The RB26 ECU is essentially the same as the 20 ECU and I knew that ging inside out. There is no facility for it to retard that heavily on cold start. The OEMs never used to do it back then. I mean, shit, the catalyst is abotu 3 miles down the exhaust anyway. Early light-off was just a twinkle in some EPA arsehole's eye back then, not a regular engine control strategy.
    • I must preface my comments with a general expression of ignorance. I have no specific knowledge of these NA automtaic things. I can only assume that the "steering wheel button" is for enabling the tiptronic controls. Wierd that it would even need/want a button for that... But anyway.... Was the car previously tiptronic? Did you put a new cluster in as part of all this?
    • Regardless, it doesn't seem wise especially on RBs to actually chase MBT. Timing scatter is the big one on stock CAS, even if that's fixed overshoot is worse than undershoot. 
    • It's all about reducing the overall output. Reduce the source of it, you have wayyyy less to deal with in every other step and trick you play with. It's why something like a modern vehicle, so VW, Audi etc, there's thousands of tables for the ECU to calculate what it should be doing with the engine.   Why would you NOT reduce emissions the most effective way possible, when it has very minimal tradeoff, AND manufacturers are always struggling to meet the current standards.
×
×
  • Create New...