Jump to content
SAU Community

Recommended Posts

out of the two id go for the integra, they look more sporty, rnt a bad performa and do handle well, i remember in a motor or wheels mag one guy got a 13.5 second pass wif a 97 version NA which is saying alot. wouldnt campare it to a turbo though....

Peugeot 206 Gti 180

133kW

202Nm

1100kg

Honda, Opel or Peugeot, you can't lose. Great chassis in all three and good power to weight. Peugeot engine isn't peaky like Hondas and comes with 17s standard. You also don't get ricer sh1t with the pug or opel.

Get an Audi A4 1.8L Turbo Quatto (1997-01)- you get the advantage of 4wd and turbo power. With a chip and exhuast you will have about 155kw and 300+nm. Insurance should be around $2k for you.

They are nice sleepers, thats why I bought one... But the biggest draw back is the tiny turbo. The A4 uses a Borg Warner K03, this runs out of puff by about 5500rpm :rolleyes: You can get the K04 which is used on the TT and S3. Then you Can make about 180kw. The good thing about the K03 is that it makes boost at really low rpm, its a little like driving a non-turbo car, the torque curve it very flat.

Or you can go a Garret GT25 - but this setup with everything included - Turbo, FMIC, S4 bumper to fit FMIC, clutch, injectors etc.. will cost over $10k. But then you will probably have about 200awkw ~270kw at the fly.

If you want to mod your car I wouldn't go the astra turbo as the turbo they use is the K03 and its on a 2 litre, so it will probably run out of breath sooner.

You can probably get a 99 for $40k. Obviously less for the 98 and 97.

If you want to know any more info on the A4 PM me. Or just ask on the forum.

Dont forget insurance also goes on value of car, so 40k non turbo Aus delivered car could be more expensive to insure then a 20k turbo import.

When in France i drove a Renault Clio, $34 k new and they are a quick little car and a genuine competitor to the Type R, or offering less performance but better looks a Peugot 206 GTi...food for thought.

  • 3 weeks later...

u got $40,000, not a astra turbo, corolla sportivo is cheaper ($10,000) and it hammers. thats $10,000 ur saving and plus its a toyota which is always a bonus. the engine has 141kw and is fun to drive...not to mention a sleeper. like my mate just brought a mazda sp20 for 28k, it looks mad but its got 98kw (which is a joke), hence the corolla, but then again i wouldnt go the new type r, the old one is a scalpel and is faster. dont get the astra...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...