Installing Ruzic Torque Split Controller

[tricstar]

got a Ruzic TSC , doesn't have much in the way of installation instructions.. I have done some work on my car Before eg, clutch, gearbox etc but nothing on the electronics side so could use some help with this one.....

most of the wiring looks to be straight forward, just match up the colours of the wires.. BUT I've pulled the dash, centre console and centre gauges, stereo etc to pieces, to connect wire to back of the front torque gauge to the + screw as described ( trying to follow instructions I found on here ) there is 4 screws with 3 of them marked os its not obvious which is the + one... is it the top right as I suspect.. ( when looking at the back of the gauge )..also is it ok to just tap into the stereo power + & - ,, as for the toggle switch can I use the aerial switch on the dash it only has two wires going to the back of it and the toggle switch only has two also, will that be ok ( the aerial has never worked but reception is fine )

If there is anyone in perth who has done this before and would be kind enough to come round and help or if anyone can just answer the questions above that would be awesome..........

[OJR32]

Try checking out this post for some tips if your still keen to try it yourself

http://www.skylinesaustralia.com/forums/As...ue-t266312.html

[tricstar]

Try checking out this post for some tips if your still keen to try it yourself

http://www.skylinesaustralia.com/forums/As...ue-t266312.html

yeah thats the one I'm trying follow, lot easier when you have someone who's done it before with you......

I see he used the stereo power, I was just hoping there was somewhere more accessable...

cheers

[some_cs_student]

The stereo power is right below the gauges (front torque split gauge) which I had to connect to, so I thought that was a logical place to get power from.

Good luck

[Duncan]

paul (mountainrunner) is on these forums if you are stuck.

good buy

[tricstar]

paul (mountainrunner) is on these forums if you are stuck.

good buy

yeah he's just messaged me and said the best place to get the power is from the same place as ECU & also I think he said the wire to back of gauge is only needed for when you use external data logging !! just waiting for confirmation of that...will post up what I find out for others....

[tricstar]

ok job done ...not exactly straight forward with those instructions and wiring diagram..firstly on all the paper work including the wiring diagram they refer to the G-sensor and then on the wiring table it starts talking about an Accelerometer ???? I asume that is is G-sensor ( if I'm wrong I've fkd it ) and also if you tap into the drivers side of the g-sensor plug (as these are wires the wiring diagram describes) then the Lateral G signal from G-sensor & lateral G signal out to computer-- are the wrong way round !!!!

anyway that was my experience ...... good luck to anyone having a go....

still haven't had a reply from mountainrunner, so I just took a punt and did it the way I thought made sense..

will test it out the track next week

[some_cs_student]

If you know how to improve the instructions I wrote please feel free to contribute, it wasn't a very difficult install but it could have been if I didn't get guidance from someone

Yes, pretty sure accelerometer is the G-sensor located under the centre console in the R33/R32.

[tricstar]

If you know how to improve the instructions I wrote please feel free to contribute, it wasn't a very difficult install but it could have been if I didn't get guidance from someone

Yes, pretty sure accelerometer is the G-sensor located under the centre console in the R33/R32.

Certainly not criticizing your instructions, couldn't have done the job without them

as the unit doesn't come with any how to....

If I get time I might add some to your instruction tread..

cheers

[9krpm]

The product is obsolete or almost obsolete.

It's Paul's hobby and not really a mainstream business.

He only made a couple for enthusiasts so there was not enough profit to put a lot of R&D in the instruction.

I think he has been making a few more as requested but he is busy with other projects now.

I intalled mine and thought the instruction was fairly straight forward.

You should get a power source that is on when the key is ON and remains on during Start.

I wired up a relay switch from the ECU.

Edited August 22, 2009 by 9krpm