Jump to content
SAU Community

R32 Gtr Veilside E3 Widebody Front And Rear Fenders And Side Skirts


Recommended Posts

finally they have arrived and i can get this group buy under way, and have them made. they will be made in brisbane

the group buy will go until 30th september. delivery is expected about 1st week october.

to start i need 5 deposits.

cost - front fenders, rear fenders and side skirts - $1750 inc GST for the set, they can not be purchased individually.

they will be made from several layers of hand laid fibreglass and to the highest quality that rivals that of vertex etc.

they can be made in fibreglass with an exposed carbon outer layer for the carbon effect, with a price to be advised.

will have actual pictures of the product by friday.

here is what they look like fitted.

post-23724-1250684548_thumb.jpg

post-23724-1250684575_thumb.jpg

post-23724-1250684612_thumb.jpg

post-23724-1250684640_thumb.jpg

  • 2 weeks later...

What will the aproximate weight be?

Can I still retain the stock front and rear bar?

Will they be straight from the mould or prepped, ready for a rub down and paint?

Can you get me a price for freight to Tasmania.

Cheers

Justin

What will the aproximate weight be?

Can I still retain the stock front and rear bar?

Will they be straight from the mould or prepped, ready for a rub down and paint?

Can you get me a price for freight to Tasmania.

Cheers

Justin

hi justin, they will be in gel coat form out of the mould, so they will need to be prepped then painted

yes u can retain the stock front and rear bars, that is what i will be doing, ill have fitting instructions over the next few days

freight to tas is $300.

whats the price with carbon overlay to melbourne?

hey, im waiting on a response regarding this.

freight will be $200.

thanks

hey ill prob run 18x12 on rear and 18x11 on front and running stock front and rear bars, i think they look heaps better than the ugly VS ones :P

ill have the offsets soon, waiting on a reply from someone who has already fitted this kit in the u.k...on wat hes running

ok so there is

1. SRB

2. XRATED

3. NXTIME?? (need to confirm still)

4.

5.

were almost there guys!

ok another one, which is 50/50 pending weight etc....

1. SRB

2. XRATED

3. NXTIME?? (need to confirm still)

4. (wishes to remain private)

5. one spot left and we have lift off!!

  • 2 weeks later...

hey the mould is being finished off this , been flat out doing all sorts of things... hopefully have some ready next week. working out the carbon overlay price this week also with the supplier, and ill weigh it up once the first one comes out, no point in weighing the once used to make the mould..

thx

hey, yes i dont see why not.. ud just have to use a GTR front bar and bonnet. not too sure on rear bar tho and the skirts may need some adjusting.

sorry been so busy lately with other shit will chase it up tomoro!

  • 2 weeks later...

the moulds have been finished and just working out the carbon skinned cost and ill start taking deposits for them to be made, all interested please pm me!

  • 4 weeks later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • So, the other thing I've sorted is a baseline dyno run up at Unigroup's new location. The auto trans was a little unco-operative by both shifting down when the throttle was floored on the dyno (so Mark had to ramp it up more slowly than in a manual) and also by shifting up at 6,000 even in sports mode instead of the indicated redline of 7,000 Still, on a hot day it made 240rwkw at 16psi which seems about right for 300kw (400hp) through an auto at the wheels.  The shape of the curve is not quite right because it was not full throttle to about 4,500 to stop it kicking down, but until I can get a tune on the auto trans control this was the best we could do.....full boost will be well below 5,000 once that is sorted, I'll get some data logs when I can to confirm For comparison, the R32 made 255 at 12psi (at 4,500) on the same dyno with tune, n1 turbos, cam gears, big exhaust but otherwise all standard so the v37 is likely a little better out of the box. One thing that is very clear is that the standard water to air intercoolers are not up to sustained use at full throttle in warm ambient temps. After about 5 runs (so only a few minutes full throttle), it was pulling boost and timing and dropping 10-15% power. Unfortunately I didn't get that printout and the Unigroup guys are away at the moment, will try and get hold of it on their return. So, looks like a healthy engine to start modifying and the only real area of concern is the w2a heat exchangers which the aftermarket has plenty of solutions for    
    • I maintain it actually looked really nice in person. So much so that I thought "No, this is illegal" but there it was, clear as day. I think we can easily call the wing and wheels/height to be transformative. Not saying it's better than the GR Whatever, or the 86, or the WRX STI or anything of that sort (the internet says it all bolts up so you can buy best of all worlds?) but it's still at least a thing and not nearly AS bad as people say.
    • That's less offensive than the previous gen.....except for all that ugly black tupperware around the edges. Blerck!
    • I leant out the window recently and took a picture of this new WRX. It looked real damn fine in person. It's faster around a track (stock) than a (stock) GR Yaris. It's much more practical despite being heavier. It's significantly cheaper. This gen tunes really well, much better than others. .... I think they're probably a lot better than people expect.
    • WRXs are a pure pleb boring car these days. You need to get an STI to even get close to what a WRX used to be.
×
×
  • Create New...