Jump to content
SAU Community

Recommended Posts

hey guys, i have bit of a problem with my r32 gtst, (RB20DET).. When i start my car cold.. it runs very well...idles at @ 1000RPM... then after 6 mins... idles drops to about 750- 800RPM.. and run rough.... then @ 11mins, the engine hunts between 100 - 1000RPM.. then stalls ( at running temp.. about 60 degrees)... i try start the engine agian then idles up to 1000RPM then stall straight away.... my dads a mechanic and we have tried everything... replaced all the vaccum lines.. checked all the intake piping... 

possible ECU problem??? or something electronic??

i would love some help guys... cheers... im running these things in my car too

## Microtech 3 Bar Map Sensor 

##Microtech LTX-12 Engine Management System 

##Microtech 4-Line Handset

##Greddy Profec B spec II Boost controller

cheers. Jamie

Link to comment
https://www.sau.com.au/forums/topic/284686-car-starts-when-cold-dies-when-hot/
Share on other sites

hey I was going to say the choice of computer was the issue too :thumbsup:

a common problem when hot is the ignitor on the back of the motor for the coils, are you still running it? If so change it for a known working one and see how you go.

Is the microguess install new? you have to be careful with injector and coil settings, you can burn things out pretty easily by getting them wrong

hey,

Moodles.. Thx for the reply... i shall try get my hands on a stock ECU .. but tht might be hard..

Duncan.. Thx for the reply... i am really new to cars and my old man is new to the jap car scene aswell.. we had a read thru the micro tech programming book.. and we think when the car is hot its not getting enough fuel wen the choke is turned off... or something like tht.... ummm also we tried programming it with the hand piece and .. "murphy's LAW" the hand piece doesnt work... or it will not do what the book says =/..... thx for the ideas...

also i dont know is the microquess install is new.. and the coil packs in my car arent stock they were changed out to "Bosch HEC715 Ignition Coils "

cheers guys, Jamie

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...