Jump to content
SAU Community

Changing Steering Fluid On S2 Stagea Rs4 ?

QLDR31

By QLDR31,
in Four Door Family & Wagoneers

 Share

Recommended Posts

QLDR31 Community Regular

QLDR31

Posted
Posted

Anyone got some tips and pics on changing the steering fluid on a S2 RS4 stagea ?

The old fluids getting a bit blackish.

It only has front wheel steering.

I haven't had a look at it yet. Do they have a drain plug or you need to take off a hose?

Thanks in advance

Brendan

Daleo Grand Master

Daleo

Posted
Posted

You could start by syringing the reservoir empty, refill with clean fluid, remove return line at reservoir, (usually on the side, bottom one is feed line to rack) fit return line into the top of a coke bottle or similar fluid receptacle, remove fuel pump fuse (stops engine from starting, needed for next step) get someone to crank engine as you add fluid to reservoir to replace fluid flowing into bottle from return line. Continue until you are getting fresh fluid from return line, (I'd have at least a litre or two to ensure you get it all out) Reinstall fuse and return line, check for leaks whilst running; Done!

Good luck!

  • 2 weeks later...
QLDR31 Community Regular

QLDR31

Posted
  • Author
Posted

Thanks Daleo

Sounds like the way to do it.

I didn't realise the fluid pumped around by cranking the engine. I thought it was just when you use the steerring wheel.

Why do you need to remove the fuse and not have the engine running? too much fluid presure ?

Stinky Rooster Grand Master

Stinky Rooster

Posted
Posted

...because the power steering pump runs off the engine, and if you bring the pump up to speed with no pressure in the lines, you may cause the fluid to cavitate, turn into foamy smoo and and make the job 100 times harder. Cranking speed "should" be fine, but if it starts coming out all foamy then shut it down, as you run the risk of this foamy smoo getting into the steering ram and it can then take a couple of days for all the air to bleed out.

Another thing - as the power steering system is a self bleeding set up, its pretty important you do all the flushing with the front wheels in the air. The best way to bleed the air out as much as possible before driving, is wind some lock on and off. And if there is any air in there, you really dont want the tyres fighting the system when its got pockets of air and no oil around the ram.

Daleo Grand Master

Daleo

Posted
Posted
...because the power steering pump runs off the engine, and if you bring the pump up to speed with no pressure in the lines, you may cause the fluid to cavitate, turn into foamy smoo and and make the job 100 times harder. Cranking speed "should" be fine, but if it starts coming out all foamy then shut it down, as you run the risk of this foamy smoo getting into the steering ram and it can then take a couple of days for all the air to bleed out.

Another thing - as the power steering system is a self bleeding set up, its pretty important you do all the flushing with the front wheels in the air. The best way to bleed the air out as much as possible before driving, is wind some lock on and off. And if there is any air in there, you really dont want the tyres fighting the system when its got pockets of air and no oil around the ram.

Foamy smoo, lol, can't believe nobody spotted that one. You guys have changed...

  • 1 month later...
QLDR31 Community Regular

QLDR31

Posted
  • Author
Posted (edited)

I finally got around to doing it the other day.

I used about 2L of fluid flushing it through. I ended up using Nissan Auto Transmission Fluid at $12 a Litre.

Only problem I had was catching the old stuff, I thought I was catching it pretty well, but ended up finding heaps on the ground.

Next up is new rotors and a diff fluid flush.

Edited by QLDR31
QLDR31 Community Regular

QLDR31

Posted
  • Author
Posted
So did you do it as recommended? Fuel pump fuse out ect...?

Yeah I followed instructions. I also added a few of my own. Cranked the engine a few times to get rid of fuel before taking the pipe off the steering tank (The pipe I removed was the rear most pipe). I also temporarily added another pipe to the tank so fluid didn't leak. I also had a few rags around to soak up the mess.

I think I made a bit of a mess because my bottle was a bit dodgie, and I didn't have a helper to catch fluid while cranking.

well there wasn't any mention of foamy smoo..... :(

It tried hard to smoo but all it could do was a few bubbles.

  • 4 weeks later...
QLDR31 Community Regular

QLDR31

Posted
  • Author
Posted
Mine is due for a change and I bought a bicycle pump to use as a syringe to suck the old fluid out. $2 at Crazy Clarks.

How did the bike pump go? I thought they only blew and didn't suck.

Daleo Grand Master

Daleo

Posted
Posted
How did the bike pump go? I thought they only blew and didn't suck.

The pump will do either, there is normally a little check valve in the flexible hose on a cheap bike pump that stop you losing the air you pump in.

  • 6 years later...
QLDR31 Community Regular

QLDR31

Posted
  • Author
Posted

Mines due again, Steering fluid is browning up.

Might see if i can get a blocker for the reservoir return this time.

At least my son is old enough to do the cranking job.

I was thinking it might be nice to add a T tap on the return to make future flushes easier. Anyone tried something like that? Probably too much hassle.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R32GTR R200 reverting from Nismo centre to stock

      By GTSBoy · Posted

      I like it when the counter chick leads you out the back into the racks and says "have a grub around in here and see if you can find what you need. I'll be back in a few minutes. Just left me in front of a massive motorised shelving system and 2-3 million fasteners, so I could find a peculiar SS shoulder bolt with cap head. Gotta love country towns.
    • Piggaz
      R32GTR R200 reverting from Nismo centre to stock

      By Piggaz · Posted

      I used this https://osgiken.com.au/product/os-giken-os-250r-lsd-gear-oil-80w250-1-litre/   shut my nismo 1.5 pro up by heaps…. Not silent though. Gives the car character and personality. It ain’t a carolla. If you want silent, put a quaife in it.
    • MBS206
      R32GTR R200 reverting from Nismo centre to stock

      By MBS206 · Posted

      It's about the same time for me from Bunnings, or the Fasteners. My big push away from takeaway food, and gluten in general keeps me away from the Bunnings Snags too! Weather up here, I've been out for two walks today in the beautiful sunshine. Had a few little drizzles, and some wind, that honestly, a tin of beans and I could compete on how harsh she blows Thankfully, being this bit inland, we're not getting anything much really. Will probably pick up a bit more when/if Cyclone Alfie decides to come ashore. A few areas in the GC though, and south into NSW are really getting smashed though! Right now, I'm just annoyed Alfie hasn't hit, as I'm not allowed to crack into the BBQ foods like the bacon and eggs until the Cyclone hits "In case we lose power"...
    • The Bogan
      R32GTR R200 reverting from Nismo centre to stock

      By The Bogan · Posted

      I love fastener joints, the price difference between them and joints like Bunnings or Super Cheap is amazing, and they either have exactly what you want, or they can get it to quick They have even given me some for free when I only needed a couple of specific size In saying this, I have paid premium for fasteners from Bunnings if they have the sizes I need, but only for convenience really, as my local is only 10 minutes away, the Sushi joint near them is also a consideration  How's the weather Matt? Stay safe mate
    • joshuaho96
      R32 update from 1990's spec.

      By joshuaho96 · Posted

      Wideband is worth setting up if only for tuning purposes. I would not mess with the ignition system unless there's a misfire. HKS crank trigger is popular out here for the relatively easily sourced Denso crank sensor, not a bad idea to install as well regardless of power level on a standalone. Boost leak test is worth thinking about. Oil pressure sensor tied to a fuel cut isn't a bad idea either. Getting the tune figured out is a good idea. Without putting eyes on it and getting under it there's no way for us to tell you exactly what it needs but most likely you're down to the last 10% that will make a big, big difference in how happy you are with the car.
×
×
  • Create New...