Jump to content
SAU Community

Recommended Posts

  • Replies 221
  • Created
  • Last Reply

Top Posters In This Topic

Just got it back yesterday, with cams in, adj cam gear, head gasket, trust plenum and larger turbine housing.  Have to wait until wednesday for the final verdict when it is being tuned:) Oh, and a nice all black Bride Brix went in:)

:wassup: that's gonna be one killer car

how do you keep rear wheel traction steve?

Are you comming out to mallala next sat?

:wassup: that's gonna be one killer car

how do you keep rear wheel traction steve?

Are you comming out to mallala next sat?

Yet to be seen about traction. As the turbine housing is two sizes larger, 0.87 vs the old 0.61, the power is alot more progressive, makes quite a difference. Before I would brake traction as soon as boost comes on, like hitting NOs, now it only breaks traction above 5500-6000rpm at WOT. But the tune, and dialing in the exhaust cam gear, will tell me alot more about how the power is being delivered.

Also, I have only run 1 bar as the car wasnt tuned, so until I wind in more I wont know exactly what it will be like. The hardmount spacers teamed up with pineapples seem to be doing an excellent job. Next will be adjustable camber arms - which will enable me to dial in some positive camber, and set it up so the rear is neutral when the car is under power.

Ultimately though, its just going to be a case of keep the boost down to where traction is manageable:)

I wont be going to the track, maybe to spectate, but I am not putting my car on a track without an oilcooler - I have all the bits (cooler, take off, remote filter mount, thermostat) just got to get them fitted and mount the cooler - which wont be happening until after this weekend unfortuneatly:(

Very nice B-man! What capacity is the new sump?

Let us know how it goes once it's tuned mate.

doglet,

I organised the ceramic coating through Shaun @ 'Boost Worx'. The coating mob are located in Holden Hill, dunno' what their name is though? All up it was $440 to coat the following;

- plenum

- throttle body

- factory cross-over pipe

- IC pipes (comp outlet to IC & IC outlet to cross-over)

- custom inlet piping

- timing belt covers

- exhaust manifold / heat shield

Steve,

Thanks mate. Mine should be back in by the end of the week. Sounds like your beast just gained a lot more potential too!

Did you know the stock inlet cam gear is adjustable too?

Adjustable inlet???? please do tell:)

I would if I knew more mate? Shaun & James have both assured me the stock inlet gear has a reasonable range of adjustment. It's a pain in the arse to adjust but then so is the ext gear. I'll let you know how we go once we've tuned my car.

Thanks R33man.

There's actually quite a bit still to be finished off in the looks department. Heaps more blue hose, braided lines, Speedflow fittings & stainless allen head bolts & so on....

The work is being done by James @ Nisspeed Performance Engines in Modbury / Shaun @ Boost Worx in Panorama & some of it by myself.

The blue hose I've sourced from all over Adelaide over the last 1-2yrs. Autobarn stock it. Most decent performance workshops stock it or can order it in.

your engine looks awesome ... now you gotta be in the next autosalon and take it out!!! :D ... yep looks much different from the last time i saw it :) ... can't wait to see in real life .. thats if you'll let me ;) ... now you can put all the greddy stickers you always wanted :D

Dean,

Thanks dude. I can't wait myself!

Hip,

Thanks mate :( Hmmm... dunno' if the car is quite up to Autosalon standard, not that I'm worried if it is or not. The engine bay should look nice once it's finished though :(

Maybe I can put a huge Greddy sticker across the windscreen? It'll make driving the car much more challenging :rolleyes:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm hoping I just don't have to do an engine rebuild NOW. Doesn't mean I won't do it at some point. I think a plus point is that the car presumably ran on or close to stock power nearly all it's life so far. Only the Owner I bought it from actually increased power with a standalone ECU and blew the OEM turbos. And after it got thee 2860s it wasn't driven an awful lot either.   That is what I meant. With the twins coming on so late (4500-5000rpm) I hope the rods won't want to exit the block prematurely. And it still being a 26 means the torque curve isn't gonna hike up all that much.   It didn't blow up on the dyno when they tuned it to 500ish crank. So I suppose it'll be okay for now. They did put a Tomei head gasket on first though which did not seal at all, and they redid it with a Cometic one. Which I hope won't be my water leak.   Mainly anything oil. So far all it has is the N1 pump, oil restrictor and a filter relocation kit with a cooler.
    • 15000? ish? Something like that anyway. It wasn;t so much a wear as a tear that then spread. Might have lasted a lot longer if not bothered by just one incident, whatever it was. I took a punt. They are really comfortable and do a good job of holding. My daughter HATED it when I first put them in, and probably still does now. She has sensory issues and hates the way they are all up your business. I'm 197cm and 95kg. Not fat or particularly wide, and the XL size seat is the rigth fit. If I was any fatter it would start to get too snug. Any skinnier and you'd possibly want the smaller width.
    • Mrs rs focus came factory with recaro cs  sportsters in it and they a pain in the ass to get in and out of with the really high bolsters, once you were in them they were one of the most comfortable seats I have ever sat in
    • The NA 2.5 has very little torque. You won't feel much. Those trannies are also a million years old now and it could well be f**ked. First generation electronically controlled autos will often refuse to kick down, ete, etc, depending on what's wrong with them.
    • Yes, but no but yes but no. Those "it's fine up to 500HP" rules and everything else like it were all determined back when the cars were 10 years old. As they are now 30 years old.....what do you reckon the chances of something shitting the bed are? I'd say they are much higher now than they used to be. You might be lucky. You might be unlucky. Spin the wheel and find out. Yeah, nah. It's actually exactly the opposite. Making boost early and having heaps of torque able to be generated right in the middle of the rev range will do more to damage an engine than having to rev it high to make the power. Think about the load on the conrods, bearings, etc, to make 400HP at 4000 rpm, vs 400 HP at 6500 rpm. So someone has already "let the Nissan out" which is how we describe the increased chance of a fiddled with engine to have had something done wrongly. Many more engines that have been opened die than stock ones do - even if you into consideration how they are treated wrt power levels and the like. Again, not saying that yours will definitely have been put back together by a moron. But the possibility does exist. It's still a lottery. Spin the wheel. What weakspots?
×
×
  • Create New...