Jump to content
SAU Community

Removing A Stage 2 Shift Kit

scotty014
 Share

Recommended Posts

scotty014 Veteran

scotty014

Posted
Posted

hi everyone i need a bit of help. i have a r34 and i bought a stage 2 shift kit for it that is already installed in a trans box. i want it installed in my car but i want to use my transmission and not this one so i was wondering how do i remove it and what does it look like so i know what parts to take down with me to get it installed.

thanks.

scott.

Link to comment
https://www.sau.com.au/forums/topic/285286-removing-a-stage-2-shift-kit/
Share on other sites
stenve Proficient

stenve

Posted
Posted

the shift kit is the actual valvebody.

if you take off the pan the valvebody is directly under that.

to get the valvebody off there is i think 7 10mm bolts that hold it into the base of the trans.

however there is about another eleventybillion bolts around the place aswell. figuring out which ones will drop down the valvebody is quite confusing.

there will also be a few different springs drop out around the place. and there is a set of solenoids. all this can be exhanged between boxes if they are in good shape.

you may also need to slightly lever out the valvebody with a screwdriver to get it to drop. its sealed on there pretty well.

i'd recommend you just take it to the shop and get them to remove and clean it. then swap it into the new car.

I ended up doing it this way. ended up costing me $400, but that was with a gearbox change also.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Stock rb25det neo questions

      By GTSBoy · Posted

      Essentially, yes. Although I wouldn't put the AFM on the crossover pipe. I'd want to put it into what amounts to the correct size tube, which is more easily done in the intercooler pipework. I bought a mount tube for card stile AFM that replaces the stock AFM - although being a cheap AliExpress knockoff, it had not flange and I had to make and weld my own. But it is the same length and diameter as the stock RB AFM, goes on my airbox, etc etc. I don't have a sick enough rig to warrant anything different, and the swap will take 5 minutes (when I finally get around to it and the injectors & the dyno tune).
    • Wazmond
      Stock rb25det neo questions

      By Wazmond · Posted

      So to summarise, the best thing to do is to move recirc to between turbo and IC, and maf on the crossover pipe. Meaning I'd need a recirc flange, drill a hole in the piping on turbo outlet area. And drill hole on crossover to fit/weld maf sensor? Either that or put the MAF on the turbo inlet right?  Is an aftermarket recirc/blowoff valve recommended? Do currently have family in Japan so could probably bring something back with maybe a cheeky lil SuperAutobacs run?
    • tsuokun
      Lets play a game - What is causing my oil consumption?

      By tsuokun · Posted

      Yep, so far most have said that it looks like corrosion on the wall from piston not moving. Which then has probably damaged the oil rings and caused those vertical marks. The longest the engine was still after the rebuild, was the winter of 2018 - 2019, plus the boat trip to Japan. When I shipped the car, it had normal gas in the tank but before that winter pause, it had E85 in tank.  In any case, even if either one of those was the cause, it happened close to 6 years ago and the car has been driven something like 30 000kms after the fact. Again, apart from the plugs and the dip stick, there is nothing in the way the car runs that would indicate what has been going on in the engine. I am going to consult a shop and ask their opinion, what would be the best approach. I do have some access to a garage I could use to diagnose further myself, but time is very restrictive. Might end up buying another engine that could be used while this one is being remedied. Without pulling the head, it will be impossible to find out if it needs another bore, but here's to hoping a hone would suffice.  Goddamnit, I would really have preferred this not happening.  
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      Boot is going to be replaced eventually. I just wire brushed what I could and rust converted. Then painted in rust kill primer. the spoiler also got repainted and plugs replaced on the ends. The under side of the bonnet is going to be black also, currently white. But red on the top side, same colour code as the silo to begin.
    • Shoota_77
      Car Rotisserie

      By Shoota_77 · Posted

      Hi guys, has anyone either purchased or built themselves a rotisserie for their car before? I can only just justify the need for one hence why I should just make one but at the same time, if I make one I can kiss another 4 weeks of potentially productive car working time goodbye because I'm building a bloody rotisserie....  I mainly want it for the application of the body deadener.  Cleaning the old stuff off, priming and then colour over the deadener doesn't worry me, it's just the application using the Schutz Gun that I feel would achieve a significantly better finish painting it side on and keeping the Schutz Gun upright.  I don't think they would work well on the side let alone almost upside down for some areas.  If the product I use (Terosun, etc) could work through a HVLP ok then it might be ok to apply without the rotisserie.   I can get one of these style ones for about $1200 which is pretty good value-     I reckon if I made one it would cost around $500 but it's more the time that it would take is more of a killer than the cost.  They look to hold their value pretty well second hand so I could always sell it after using it and realistically only lose $200-$300 at worst.  Or keep it and buy another project when this one finally sees the light of day... Anyone selling one...? Cheers!  
×
×
  • Create New...