Jump to content
SAU Community

More engine oil discussion.


JimX
 Share

Recommended Posts

I've read several oil articles, some contradicting the others, and some talked about in here. But I think we're about due for another one especially with the server crash and all :D

This came about because I went into Autobarn in Chatswood looking for some 10W-40 synthetic Motul oil, which a guy at Auburn Autobarn who also owned a Skyline had recommended for my car (mild R33 GTS-t). In the end I could only find 5W-40, but the "40" was the important number and I'm already running Castrol 5W-30 and I just wanted something a bit thicker for summer.

So I took it to the counter and asked for a filter as well, and the guy said "You're not going to put that oil in your Skyline are you?" and I said yes, and asked why he thought it was a bad idea. He said that it was too thin and I should be running at least 15W-50 oil. I told him that I had been running 5W-30 for the past year or so with no problems. He still seemed wary, and he said that the 40 oil should be ok as long as I don't do any track work or too many mods. I bought the 5W-40 oil anyway and I'll put it in soon.

So anyway it got me thinking - I have known for awhile that thicker oil is necessary for really powerful engines, but aside from that the thinner you go the better. But now it's got me thinking - where is the cutoff point to where you need to run thicker oil?

I know that the drag racing tomato farmer guy (forget his name) runs Castrol 15W-50 oil (the only mineral Formula R in their series) and his car is like over 1000hp. So I'm guessing that 5W-40 oil will be fine for my car which is :D

The funniest thing here is - Two different stores from the same franchise, and completely different advice from each store!

Link to comment
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

dude a guy at autobarn told me i needed a 15w50 and i tried it and it ran like an absolute slug.... i changed it back immediatly to a 5w40 and the car runs better than ever

u need to oil upto the turbo quicker so a thinner oil at startup is neccecary

Link to comment
Share on other sites

I'm pretty sure factory spec oil for the R33 GTS-t's is 7.5/40w.

It's too hard (and expensive) to find 7.5w oil unless you use the nissan stuff, so that's why most people go for 5 or 10w.

I wouldn't use 15w, it's just too thick....

Stick with the 5/40w I say :D

J

Link to comment
Share on other sites

jimx

victory bray is the tomato farmer in question and his race car is and has been for many years sponsored by castrol. the engine is a 2500hp keith black that has an oil change every run... his oil his not really related to what we should be using.

i've used only 5-40 grade and am thinking of going to try the 10-40 as my oil pressure is pretty much always on 2 (8 max) on the factory gauge. it drops below to about 1.5 at hot idle. i'm thinking i stay with the same brand as the pressure never drops or peaks heavily.

15 - 50 is around what i ran in my old red motor!

Link to comment
Share on other sites

NO NO NO NO NO!!!!!!

dude, if you had ANY MOTOR AT ALL with clearances as big as some big hp v8's you'd be running the heavier stuff.

Clearances in our Jap, injected motors are dramatically smaller and as such, too thick an oil will root things (performance, eng life etc) remarkably!

I know a lot of guys that run 0W 40 in their cars.

Is thin - Is good!

Adrian

Link to comment
Share on other sites

Me old HQ had a worn 253 in it, and to stop oil bruning, I was told to put a 40/70 oil., It was so god dammed thick, it stop the smuldering, but it reved so much slower. THe engine was working against the oil.

No much sooner anyway did that oil start slipping through and it was time for a engine rebuild.

Stay thin, unless you start loosing oil, go a grade up, because as your engine ages, the engine loosens up and thin oil will start to slip through the rings or valve guides.

So as long as you aint loosing oil, stick to a thin oil.

My 2 cents.

PB

Link to comment
Share on other sites

Guest RedLineGTR

yep factory is 7.5-30w

u can get that type of oil from some places but it cost to much so its not worth it. Stuff that i would use is 5-40w 10-40w 10-50w at most i know of a highly modded GTR that uses 10-60w but when i used that in my car the oil pressure was way too high so i switched back to 5-40w..works fine...as for track days usally u chnage your oil before or after a track day anyways depends how hard u are driving to make sure everything is okay

Link to comment
Share on other sites

Adrian,

obvious you read my post wrong or i worded it badly as you, after saying NO NO NO NO, said exactly what i said in your post, ie bray's oil close to what i ran in my red motor but NOT what you run in turbo jap motors.

sorry, i just hate being hinted to as a drastic idiot when i have been working on my own cars for close around 9yrs

i run helix ultra synthetic and my oil pressure never gets above 1/4 the way up the gauge. if thats normal for a skyline then cool but i'm used to oil that fluctuates pressure a bit more than that.

Ben

Link to comment
Share on other sites

yeah i didn't word either of my replies all that well

oh well,

me good england, me speak you well..

anyway, anyone have any major grievances with helix ultra what ever it is (0-40 or 5-40 - i cant remember atm - stupid short term memory). The 5000km is up and was wondering in anyone can suggest any other oil sub $60

Link to comment
Share on other sites

30wts are a lil thin for our damn hot summers. 40wt is pretty ideal for the amount of ks we have on our cars coupled with the hot heat. 50wts should only really be used in oil burning engines or if you do alot of track work. Our jap engines run very tight clearnances compared to aussie/usa cars so a 50wt is not really ideal IMO.

Dont worry JimX, 5W40 you got is pefectly good!

Link to comment
Share on other sites

5W-40 is probably good enough all year as long as you don't give the motor a hard time when it's hot (which is bad for it in ways besides lubrication anyway).

I wanted slightly thicker for summer but I'm sure 5W-40 will do OK.

Wouldn't really be keen on using a 0W oil though. You do need to have some viscocity!! :P

Link to comment
Share on other sites

I was running 5W-30 up until now because it was close enough to factory spec. But the guy at Chatswood got me thinking, even though I didn't trust his advice of running 15W-50.

The factory spec of oil thickness is for a stock standard engine. Up the power and at some point you need to increase the viscosity. Not to mention thicker oil is needed for our hot summers. But even with that consideration I think the 5W-40 was a good choice, with 0W-40 or 10W-40 being ok as well (as is the general consensus).

I now think that 30 is the bare minimum thickness, with 40 being pretty good and anything more either there for track work or desert driving, or just a waste of power. If I was going to run a 50 weight oil it would be 5W-50 too, not 15W-50.

Oh and yeah thanks for reminding me of Victor Bray's name cul202 :P

Link to comment
Share on other sites

Originally posted by cul202

anyway, anyone have any major grievances with helix ultra what ever it is (0-40 or 5-40 - i cant remember atm - stupid short term memory). The 5000km is up and was wondering in anyone can suggest any other oil sub $60

The Motul 5W-40 oil I bought was called "8100 X-CESS" and was $55 from Autobarn. It's 100% synthetic and says that it's good for turbo cars on the back of the bottle. It's got a high level of detergent and so should be good for keeping carbon buildup off the inside of your engine.

Link to comment
Share on other sites

Was "NO NO NO"'ing to whoever the crocodile was that gave that advice to JimX

What I said after that was re-iterating what you said to make your point stronger.

All good!

Adrian

Link to comment
Share on other sites

Lower numbers are thinner. So 30 is probably too thin :)

Well as I've said I've been using 30 for most of this year without any problems. It's mainly the extra heat of summer that's making me want to go thicker, and also now the extra power output I have.

Link to comment
Share on other sites

I think for $80 it's probably better quality than say Castrol 5W-30, but I'd still want to be changing it every 5000km and that is a hell of a lot of money to be spending every 5000km. Also at $80 I don't know how much of that money is going into quality and how much into the name. With the Castrol oil a lot of it is in the name, which is why I think the Motul oil I bought is better even though it costs around the same as Castrol's cheapest synth.

Yours should be ok, but I wouldn't flog it too hard on a hot day in summer. But then, I think I wouldn't do that anyway with any type of oil in the engine unless I had an oil cooler.

I've heard a few people say that "Gold" Mobil oil is overrated and overpriced. If you wanted to swap it, maybe try their 0W-40 or 5W-50.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
    • You can just get the injector bosses, which allows top feeds to fit. He can use the same injectors without issue, like these (another option): https://rocketindustries.com.au/af59-2210-rb25-fuel-injector-inserts     The Racework ones look a bit better: https://www.nzefi.com/product/raceworks-lower-injector-mounting-boss-kit-for-r33-rb25det-s14-s15-sr20det/   You could also just get a similar kit like the Radium one by Plazmaman: https://plazmaman.com/product/nissan-rb25det-r33-billet-fuel-rail/?srsltid=AfmBOoogfYq49X0fu2Wdbf8yOf6zt9egyPAif_gn3Qr3G8hzAphhTgOkO70  
×
×
  • Create New...