Jump to content
SAU Community

Hks Ssq Bov On R33 Gtst

Braddd

By Braddd,
in Engines & Forced Induction

 Share

Recommended Posts

Braddd Enthusiast

Braddd

Posted
Posted

hey

just wondering if anyone has a HKS super sequential blow off vave on their R33 gtst? if so, are you running it with stocker ecu? i was told that because its not plumbed back, it makes the car run slightly rich and not quite right?

so im basically asking, is it ok to have it on with a stock ecu?

cheers.

Link to comment
https://www.sau.com.au/forums/topic/286349-hks-ssq-bov-on-r33-gtst/
Share on other sites
geraus Mentor

geraus

Posted
Posted

Hey there, You can run it no probs . But your going to encounter many problems such as:

stalling

running ruch

backfiring

you car wont run smooth

idle hunts....

I use to have one on my 33 when it was a stocker, it sounded pretty sick! :happy: but i got over it. Yes/No it will be ok because your car will overfuel.

mosquitocoils Veteran

mosquitocoils

Posted
Posted (edited)

Some people run VTA bovs (like your SSQ) with stock ECU and never have a problem, while other's will stall all the time, backfire etc etc. I think some people try resetting their ecu after installing a VTA bov, dunno how much it really helps though.

Edited by mosquitocoils
bradnkaila Enthusiast

bradnkaila

Posted
Posted

I have one with stock ece and mine runs fine, sounds wicked, no stalling and runs smoothly.

I dont understand how an aftermarket bov can make your car hunt at idle??? im pretty sure a bov does nothing at idle.

Savin Collaborator

Savin

Posted
Posted

have you tried adjusting the back screw on the back? when i installed my hks bov my car keep stalling in the lights...but wen i adjusted it to open the valve just a little bit ...it runned the way i wanted it. hope this helps you

ShaolinCurse Collaborator

ShaolinCurse

Posted
Posted
Stock BOV's leak at idle, aftermarket items do not.

This can cause problems quite easily

hi,

sorry new, but did u explain this the wrong way around?

wouldn't leaking be the cause for stalling?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Shoota's R33 GT-R RB30/26

      By MBS206 · Posted

      I was more thinking so it doesn't flop around as much rather than for rotating it. Once you have the balance right, it should rotate well enough, depending on how much resistance there is on the pivot. I think you said the pivot point was on a bearing though didn't you?
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      You can get them with the worm drive rotator but I was too tight to pay another $250-$300 so manual labour it is! I don't think it will be too hard to rotate though. 
    • MBS206
      Left & Right Window Regulators for 2013 Skyline V36 Coupe

      By MBS206 · Posted

      Sag as in the windows start to slowly open themselves, or they're just slow to go up/down with engine off?
    • MBS206
      Shoota's R33 GT-R RB30/26

      By MBS206 · Posted

      It looks like it needs a big worm gear drive on it to control the rotating, not a few sloppy pins!
    • MBS206
      R32gtr sputtering and stalling

      By MBS206 · Posted

      As Duncan said, first there was OBD, which few cars used, then came OBD2.   Now an interesting point, OBD2 isn't even for what you want to do. OBD2 is for emissions testing. There is some sensor data on OBD2, but it's up to the manufacturer what they're putting on it. Most scan tools operate on UDS, which like OBD2 is a standard built on-top of CAN. UDS specifies how to structure a message, what very limited things mean such as "read memory address" but it does not specify what is stored in which memory address, that is all up to the manufacturer. You either a scan tool compatible with that vehicle, or to know how to reverse engineer all the data, which can take a VERY long time and a lot of vehicles to get it right. Oh and then the manufacturer does a firmware update and changes what's where... Ask me how I know that as fact Oh, and by the time you've got the scan tool that supports all the manufacturers stuff, well, you're back at "But a consult cable and the Nissan software" The main difference being most manufacturers software these days works with the same hardware readers, as the readers are built to support J2534 which is another standard for how the PC communicates with the tool to make it do specific things on the car...
×
×
  • Create New...