Jump to content
SAU Community

Garrett Gt3076r

nizmo da gizmo

By nizmo da gizmo,
in Forced Induction Performance

 Share

Recommended Posts

nizmo da gizmo Collaborator

nizmo da gizmo

Posted
Posted

Hey guys , i was wondering what power can the Garrett GT3076r hold? I am just wondering because later down the track i am rebuilding my RB25 and need a turbo setup. I do not know much about turbos i'm still new to the scene.. But would be much appreciated if someone could help me thanks!

Link to comment
Share on other sites
conan7772 Mentor

conan7772

Posted
Posted (edited)
Hey guys , i was wondering what power can the Garrett GT3076r hold? I am just wondering because later down the track i am rebuilding my RB25 and need a turbo setup. I do not know much about turbos i'm still new to the scene.. But would be much appreciated if someone could help me thanks!

I think NYTSKY is probably the best example.

He's done a thread on his engine build.

363 rwkw.

PS, stick with external waste gate.

Edited by conan7772
Link to comment
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • lizaliam
      R32 GTR Pre-purchase inspection - Brisbane

      By lizaliam · Posted

      For students aiming for top grades, our Best Assignment Help offers the perfect solution. Our team of experienced writers delivers meticulously crafted assignments that meet university standards. We prioritize originality, timely delivery, and round-the-clock support to ensure your academic achievements.
    • IXMandalorianXI
      Wheel offset has me confused.

      By IXMandalorianXI · Posted

      I should clarify that the previous owner put the wheels on, so Im not entirely sure what he bought. I was searching the Rota page and found these two as the only matches. It did not occur to me that perhaps they sell these wheels with different offsets. I guess the best way to solve this is to take the wheels off and measure them from the inside to be sure.
    • Kinkstaah
      Wheel offset has me confused.

      By Kinkstaah · Posted

      The offset doesn't really have anything to do with dish directly. I mean it kind of does but it also doesn't, it's only tangenial. The offset is purely how much offset (get it) the mounting face is from the CENTER of the width of the rim. I.e, the mounting face would be directly in the middle of the 9.5inches if it was a 18x9.5 ET0 rim. Given it is a +12 rim, the mounting face is 12mm further away from the center (to the outside of the car). Your fronts are +30, so the mounting face is 30mm further away from the center (to the outside of the car). I would wager this doesn't look right, because most skylines generally have the same with guards front to back. So I'd think your fronts look significantly more sunken in than your rears. I'd wager by about 18mm, or so.
    • IXMandalorianXI
      Wheel offset has me confused.

      By IXMandalorianXI · Posted

      My '96 r33 Skyline has Rota GTR, 18 x 9.5 inch, ET30 on the front and Rota GTR-D, 18 x 9.5 inch, ET12 on the rear. (Put on by previous owner) The 12mm offset is throwing me for a loop. Is it due to the "deep dish" design of the wheel that the offset it so low? Or is it actually that low on the rear normally? If I were buying a set of new wheels, could I put 30mm offsets on the rear and reasonably expect them to fit? I have GTR Brembos and 370Z rotors (355mm/350mm) if it matters. Thank you.
    • JC71
      R34 GTT air noise?

      By JC71 · Posted

      here is the video, again really hard to hear but in person its very loud 20240703_175734.mp4
×
×
  • Create New...