Jump to content
SAU Community

Rb20det Ecu With Nistune Chip, Suit R33 (manual) $350 Ono

W3P3N
 Share

Recommended Posts

W3P3N Contributor

W3P3N

Posted
Posted

Bought this RB20DET ECU off another forum member and purchased the nistune chip and had it installed through nistune in Adelaide.

From what i understand they loaded the base map in for the R33 but you still need to get it tuned to get it to run.

I was gona put it in my R33 Series 2 but got it dynoed on monday on the Stock ECU and Turbo and made 199kw on 10psi, im stoked with that.

I have no more need for it anymore it cost me $450 all up, im after $350 ONO, Will post any where in Australia.

Any questions Please Ask, Thanks Ben

post-60037-1252576819_thumb.jpg

32_Dave Mentor

32_Dave

Posted
Posted (edited)

how do u use the software without the individual license?

also does it come with tuning cable?

Edited by 32_Dave
W3P3N Contributor

W3P3N

Posted
  • Author
Posted

I dont have the cable but its available off the website for $105, The Software and Individual License is availble of the webite for $200, or you can just take it to a tuner who tunes nistunes as thats what i was planning to do.

32_Dave Mentor

32_Dave

Posted
Posted (edited)
I dont have the cable but its available off the website for $105, The Software and Individual License is availble of the webite for $200, or you can just take it to a tuner who tunes nistunes as thats what i was planning to do.

shit...

Edited by 32_Dave
W3P3N Contributor

W3P3N

Posted
  • Author
Posted

Just got this off the website

Type 2 boards cover the following earlier consult vehicles:

M30 Infiniti (VG30DE)

Z32 Fairlady 300ZX (VG30DETT)

[Note ECR33 RB25DET Skyline can use Z32 VG30DETT ECU with minor wire swapover]

HCR32 Skyline (RB20DET)

BNR32 Skyline (RB26DETT)

[Note BNCR33, BNR34 Skylines can use BNR32 RB26DETT ECU and O2 sensors]

U12 Bluebird (KA24E)

I would say 99% yes, Email Matt at [email protected] if you wana make sure

.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By dbm7 · Posted

      For sure the later RB26 variants had a different setup (6 cam voltage sender?), but the RB25DE/DET share the same ECU pinout/PCB footprint, and at the ECU plug it ends up being 'throttle sensor in' & 'throttle sensor out' (to A/T TCU) ...you stick a multimeter on these pins and you'll find them directly connected (0 ohms) ; I had an pair of Nissan ECUs on the bench long ago, and I noticed this throttle sensor in/out link, actually linked to an op-amp ...which was unpopulated on the NA board, but present on the T board and I went 'ah-ha!' in some moment of clarity... ...it wouldn't surprise me if they changed strategy here though (in the software and actual monitoring of this signal), because they did with other stuff (A/T signals).. and 0.45v as a trigger point makes sense, as that's what the external TCU units expect at idle ; kudos, thanks for that insight...I suppose it boils down to whether or not Consult can display real time data of that signal's voltage... ...in any event, it presents the same target...ie; rotate TPS unit to achieve 0.45v to suit both ECU&TCU, and where do you goto from there? Just disconnect TPSwitch connector and/or that plus TPSensor connector....or do you go for the throat and disconnect IACV solenoid and see if it still stalls? (probably throws a recoverable fault code and goes for default idle strategy?)...
    • PotatoCake
      Exhaust silencers/varex exhausts

      By PotatoCake · Posted

      I’m also conscious that e85 is slowly being phased out. Not all United’s have them anymore. Can’t take the risk of being low on petrol and assuming the servo will have it. 
    • The Bogan
      NC MX5

      By The Bogan · Posted

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      MR HAMMER has said his piece. Painted up to avoid Rusty Rusty. Actually lines up well. (i.e it lines up the same as the unmolested GTR guard). Turns out the GTR Strut brace does foul on the bonnet vents ever so slightly. May need a little bendy bendy if intended to keep using with a strut brace. So spacing it out to clear the FAST102 is not an option. Annoyingly, the bonnet vents also foul on the heater lines running over the engine. Given this engine does not EVER require a heater, a delete loop is going to be used. Don't worry, the defogger uses the AC. The heater is basically "Do not use the aircon and turn the fan on". It will still be effective, I promise.... once I get the system regassed... Will have to revisit with unvented bonnet I suppose, and suitable strut brace. There's plans to do this and other things tonight and bleed brakes (there was a weep) and put the bumper back on, and take Good Friday morning - Because troubleshooting on the side of the road limping it home at midnight tonight is ... not very smart.
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      Thank you all for you assistance. I contacted Nistune regarding the support for the RB20DE along with my ECU Code (23710-10U00). They do have a map for it and added the RB20DE as a purchasable option now as well. They also added Malta as a Billing and Delivery options as this was missing. I was honestly amazed at their quick response and action, it took less than 24 hours. I also looked again at direct fit options for injectors, just in case I were to replace them. DeatschWerks seem to use a Bosch EV14 base and makes ones that fit mine at 440cc lowest, but also have 550cc at the same price. I tried looking for other direct fit options and managed to find one (also Bosch EV14 based) which includes a plug and play adapter on ebay. Did a small test with a Noid Light on the troubled injectors and all seems good, so they are pulsing properly electrically. One weird part is that they are missing on the same two cylinders as before I got the injectors cleaned. Mechanic also found this weird as he did not label the injectors and it is unlikely to have the faulty injectors be installed in the same cylinders.  
×
×
  • Create New...