Jump to content
SAU Community

Recommended Posts

sorry if this has been discussed before but i wanna up the boost in my car without spending big bucks cause as u all know i'm a tightass ... what i want to know is if there are any differences in performance of different brand bleed valves eg gfb or turbosmart or greddy etc .... why overshoot occurs?? how bad this problem really is?? and also if anyone here has stuffed up a good engine by using a bleed vavle ??

thanks

Link to comment
https://www.sau.com.au/forums/topic/28752-bleed-valves/
Share on other sites

There's nothing too special about the name brand bleed valves, Theres a shit load of guys out there who run homemade bleeds and if they are made and setup correctly you wouldn't have a problem with them.

The problem with bleed valves is they cant maintain the higher boost all the way to redline unless you set them up with a lot of piping and if you do then you will get a lot of spiking. Thats the trade off.

The greddy on the otherhand is a regulator type controller rather than a bleed and are a shitload better at maintaining higher boost to redline and have minimal spiking.

I'm in the process of building a home made regulator type controller and turfing my bleed valve.

Heres a link if you're interested

http://www.autospeed.com/A_0670/cms/article.html

Have fun

Link to comment
https://www.sau.com.au/forums/topic/28752-bleed-valves/#findComment-593536
Share on other sites

i wanna up the boost in my car without spending big bucks cause as u all know i'm a tightass

good to know theres still honest men around! haha icon14.gif

I had a simple $100 turbosmart i think? bleed valve on my previous car and it did the job, I think i was one of the lucky ones though as mine used to hit about 14psi and bleed back a little bit rather then spike.

I think if your planning on running more boost in the future (turbo upgrade) etc you may as well outlay some more pennies and get a electronic one

Link to comment
https://www.sau.com.au/forums/topic/28752-bleed-valves/#findComment-593550
Share on other sites

yeah .. i'm not going to plan to put on a bigger turbo or anything like that ... i just want that little bit of extra power ... got a full exhaust and pod ... but my boost is still very stock ... it only just passes 350mmhg in second (auto) ... but in first its just under 350mmhg ... and before i had those mods it was never ever passed that half way mark ... so yeah i just wanna put it up just that little bit :cheers: ... i wouldn't mind having a dyno but i doubt it'd be worth it ... i've got a proper boost gauge which i will put in soon just to see how accurate the stock one really is ... cause i thought those mods would of upped the boost more than it did ... but we'll see ... :D

Link to comment
https://www.sau.com.au/forums/topic/28752-bleed-valves/#findComment-593658
Share on other sites

I don't entirely agree with what BHDave said about bleed valves. The ones that most guys make are generally pretty shoddy. they don't hold boost (bleeds back by like 5psi) and they spike something chronic or from what I have personally seen which is 7 examples if I remember correctly. Another reason to buy A brand name one is becasue some of these have a brass restrictor in the valve itself. This is designed to try and stop (read curb) wastegate creep. Turbosmart calls it something like GBC gated boost controller or something like that.

Link to comment
https://www.sau.com.au/forums/topic/28752-bleed-valves/#findComment-594090
Share on other sites

I'm in the process of building a home made regulator type controller and turfing my bleed valve.

Heres a link if you're interested

http://www.autospeed.com/A_0670/cms/article.html

Have fun

I was in the process of building the same thing but then I got the PowerFC + Apexi boost controller.

So anyway I have the parts required to make this device if anyone is interested in buying them.

That is:

1 x R07-200-RNKG Inline 07 ¼ Regulator Relieving 7Bar;

1 x V07-200-NNKG Inline 07 ¼ Relief Valve 7 Bar;

2 x 2069-02 07 Spring 0.7 Bar (brown);

I have already installed the 0.7 bar springs.

Link to comment
https://www.sau.com.au/forums/topic/28752-bleed-valves/#findComment-594299
Share on other sites

i am running a gfb bleed valve with my auto r32gtst and it works a treat! doesn't spike (although the hoses are very short) which many people claimed thaty would happen.

from what ive read the turbosmart ones are the most unreliable, while turboXS makes a very good one. GFB also no problems from first hand experience.

it actually loses about 1-2psi above 5000rpm but that i would expect from the stock turbo at 11psi and i don't think this is a bleed valve issue so much.

good luck and happy buying!

Waz.

Link to comment
https://www.sau.com.au/forums/topic/28752-bleed-valves/#findComment-594581
Share on other sites

As a side note (as people normally do this when they fit a bleed valve) is it safe to disconnect the boost solenoid (without fitting a bleed valve) ie just to get rid of the two stage boost?

Is it as simple as disconnecting it? Or do you have to feed it 12V? Does it cause any harm just disconnecting it without feeding it 12V?

Sorry for all the questions, im a newbie :D

Link to comment
https://www.sau.com.au/forums/topic/28752-bleed-valves/#findComment-594896
Share on other sites

As a side note (as people normally do this when they fit a bleed valve) is it safe to disconnect the boost solenoid (without fitting a bleed valve) ie just to get rid of the two stage boost?

Is it as simple as disconnecting it? Or do you have to feed it 12V? Does it cause any harm just disconnecting it without feeding it 12V?

Sorry for all the questions, im a newbie :rofl:

i'm not sure how to install it either .. clint .. dean .. i may need ur help :)

Link to comment
https://www.sau.com.au/forums/topic/28752-bleed-valves/#findComment-595060
Share on other sites

Disconnecting the solenoid is not a problem. The ecu does not know the difference. I ran my solenoid disconnected for a very long time.

Did you just purely disconnect it? or did you feed it 12V (I read another post about someone feeding it 12V supposedly to keep it happy).

Is there a way to know whether its working or not? I guess the easiest way would be to keep an eye on the boost gauge and see if boost comes on in two stages...

You'd think that the eCU would know if the solenoid wasn't connected and report some error.

Link to comment
https://www.sau.com.au/forums/topic/28752-bleed-valves/#findComment-595568
Share on other sites

i'm not sure how to install it either .. clint .. dean .. i may need ur help  :P

Hippy, dont be scared:) its easy. Just cut the vacuum line to the wastegate actuator, and put the valve in line with the solenoid. Then unplug the factory solenoid.

The factory solenoid is a type of bleed valve, when the revs hit 5000, it bleeds off enough air for 2psi extra boost.

The valve you are fitting, just allows a small amount of air (boost pressure) to escape to atmosphere, and therefore not being used to actuate the wastegate.

simple.

To adjust, wind the bleed vavle all the way SHUT, so all boost pressure is going to the wastegate, then back off 1/2 turn. Take for a spin, then repeat until you have the desired boost pressure, recommend not going over 10-11 psi with stock cooler.

Link to comment
https://www.sau.com.au/forums/topic/28752-bleed-valves/#findComment-595746
Share on other sites

Guest MFX_R33

I have a homemade bleed valve, set up as a 2 stage. It cost me $70 buying the parts from Peps, and it does the same thing (I would say better than) the Turbosmart equivalent. The difference with mine is that don't have a fixed restrictor, which plays the biggest part in controlling the boost. I use and adjustable ball valve, to set the restriction. I have then used a fuel lock solonoid with an in cabin switch for the 2 settings. It is cheap simple and it works well. I have used it to the tune of 205 kw @ rears with 18psi and a small drop off towards the 7500 redline to 16 psi.

Jeff.

Link to comment
https://www.sau.com.au/forums/topic/28752-bleed-valves/#findComment-596172
Share on other sites

I might hijack this thread temporarily so i can diagnose my problem. My bleed valve is currently not really workin rite.

I have a hose comin from my intercooler piping into the bleed valve, and then this into the wasgate actuator. Is this correct. At full antilock on the bv, i get stock boost, and at full clockwise, i basically get either uncontrollable boost or exactly the same as stock.

I dont know wats goin on. It must not be correctly installed?? I just recently installed a FMIC, would this change anythin?

Link to comment
https://www.sau.com.au/forums/topic/28752-bleed-valves/#findComment-596481
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Actually,  just remembered there should be info in the threads (somewhere) about swapping to a manual steering rack and deleting power steering all together. 
    • Also had a look at the Nissan JP website looks like the 400r has a slightly shorter ratio than than the regular V37 3.133 VS 2.937 which from a guy who has driven both 3.69 vs 4.11 ratios in the S15 is bugger all. Seems that the AUTO Z runs the same ratio as the 400R but can't find any info as to if its an open or LSD? More often than not the auto LSD is open
    • Do not replace the power steering lines with this stuff. If it's anything like the Chase Bays stuff it will leak and be worse than stock. The reason why the reservoir is on the LH/passenger side of the car is because that's just where the reservoir was most convenient to fit. Don't overthink this stuff. The intake/cold side of the engine is pretty busy on these cars. And again, the hardpipe is designed to be a janky power steering cooler. In theory you can replace it with a real power steering cooler but that's really only for track use where boiling the fluid is a distinct possibility. Start with the low pressure lines feeding the pump from the reservoir. Make sure there isn't a bunch of junk in the reservoir filter. Be careful to not get ATF all over the engine bay. I hate dealing with ATF spills, you can clean it up and the slightest crevice will still release more oil that can still drip over time. You also want to inspect for leaks before you make a mess and can't tell what happened. Most likely you have a leak somewhere that is allowing fluid out and air in. Failing that it's allowing air in but not fluid out. Only place I can really see that happening is on the low pressure side because the pump will pull a slight vacuum to draw fluid in. Everything after the pump is high pressure or lower pressure, approaching atmospheric by the time it returns to the reservoir.
    • I did a skidpan night at SMSP this week, it was much cheaper than $350. But yeah, you need to slap an LSD in that thing.  I put an OS Giken in the 370Z and it's f**king MARVELOUS even compared to Nissan's viscous LSD. So you're saying it's free now that it's a housing estate? 😂
    • Nah, the car seems to run exactly as it did prior, in saying this it does "seem" to be better down low, like more eager to rev, but that may be 100% placebo effect from intake noise But, I'm not worried about it at all, in the end it is a fairly low compression NA engine that has a well shrouded intake,  if it is getting hotter IAT I cannot notice anything negative performance wise from the seat of my pants thrashing it about on the street or sitting in traffic, so meh, car now now makes induction noise so I'm happy
×
×
  • Create New...