Jump to content
SAU Community

Built Rb26


Recommended Posts

I am having no luck selling my stagea so i am considering selling the built motor seperatley and going back to stock to sell the car easier.

Motor spec's:

11,000km's and 13 months old mostly highway kays (100km round trip to work), never been raced etc, never gone over 9psi.

Built by Gavin Wood Autotech on the gold coast

Arias pistons

Eagle rods

Trust Metal head gasket

Trust 264deg easy street cams

Tomie sump baffel

Tomie oil restrictor

ACL race series bearings

All new gaskets

All new timing gear

New garret 2860-7's

Head fully recon'd and lifters set for the cams

Fully balanced

Block and crank crack tested

Block acid dipped, decked etc

Crank linished

N1 oil pump

New water pump

Apexi power FC with hand controller, newer version AFM type

Engine did 304awhp @ 9psi at xspeed who did the tune

I have receipts for over $8000 in parts and machining alone not including any labour building it.

Im chasing $10,500 ono which i think is fair considering the work done.

Or $7000 with a stock R33 GTR motor as a trade i can then put into my stagea.

I am selling the motor to fund some work on my R34, i may consider other parts with the trade (man conv, R34 GTR rims, coilovers etc)

The motor is still in the car, i will not pull it out until i have a deposit as i still need the car. Inspections welcome.

I am in Bunbury WA

0419943997

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Hey guys any recommendations for fitment for a stock 94 GTR R32  Want to order work meister s1 3p and would like a nice looking flush fitment. Plan to get MCA coilovers to set ride height etc. Just confused on offset, brake clearance etc.  Never purchased after market wheels so I'm a bit concerned since it's a long wait to order and I don't want to order the wrong specs. 
    • Update: Done: -Running on 6 cylinders, one injector was gummed up. I made an injector tapper, bit of Teflon on the end of a metal rod.  That fixed the injector. Need to replace one injector plug, the fastener is broken. -Coolant bleed -Fixed 4WD warning light, bleed 4wd system -Fixed electrical problems: alarm, brake lights, various broken plugs  -Got all the parts ready to connect head drain. Head drain is fitted with a blocker atm Todo: -Fuel pump dead, Been cleaning out the tank, had a lot of tobacco looking stuff, think its OEM foam. Got a Walbro 460 to put in. Probably going to add a relay to give the pump a solid 13volts. Replacing all the fuel hoses, in tank etc. -Front drive shafts still not back on. Waiting on parts. Would like to buy some new ones, but probably going to patch these up for now -Replacing gas struts on back door. Waiting to be returned -Headlights need a polish/repair -Going to touch up the paint a little. -Clean up the interior -Connect up heater plumbing -Cosmetic stuff, powder coat replace rusty parts, replace rusty bolts, wiper blades, silicon missing rubber -A million other things
    • Don't do this unless it never gets hot where you are.
    • Upgrade time. Been a long time coming, but I was able to get my GTR to a reputable builder in the States. List of upgrade parts below: RB30 (Sourced from Australia) PRP RB30 timing belt kit with all options Nitto pistons Nitto I beam rods Nitto oil pump King engine bearings New RB26 Head (Grabbed during Heritage run) Kelford 272 cams mild lift Supertech intake and exhaust valves over sized Nitto Head gasket Greddy Oil Pan Sump GKtech fan blade and adapter Koyo Radiator Borg Warner S362 SXE 6boost turbo manifold T4 divided  Turbosmart wastegate Pro-gate 50 lite ID1340x injectors Radium external surge tank Walbro 450 fuel pumps x2   All Parts in hand and awaiting my turn in line at the shop! 
×
×
  • Create New...