Jump to content
SAU Community

Recommended Posts

They're both pretty shit and I'd take a $37 turbotech over either of those. The only EBC that's worth getting IMO is the Blitz SBC i-D Spec R. It actually brings on boost hard and holds it there as well as being very easy to configure, even in manual mode.

They're both pretty shit and I'd take a $37 turbotech over either of those. The only EBC that's worth getting IMO is the Blitz SBC i-D Spec R. It actually brings on boost hard and holds it there as well as being very easy to configure, even in manual mode.

Have you actually used the gizzmo msibc?

From all the reports i've seen and heard it is quite a really good little unit.

Having had the avcr in my old car, i'd definately go the gizzmo.

I like my Gizzmo MS-IBC, its simple, cheap and to the point, wastegate pressure (gain) and boost pressure (duty cycle) is all I ever needed, I use all 6 boost memories for different boost settings (10psi to 14.7psi) and various gain settings for violent or normal boost building.. it's an Australian product with Australian support (Ray knows his stuff) so can't go wrong. Very easy to hide, both the controller and the solenoid.

I like my Gizzmo MS-IBC, its simple, cheap and to the point, wastegate pressure (gain) and boost pressure (duty cycle) is all I ever needed, I use all 6 boost memories for different boost settings (10psi to 14.7psi) and various gain settings for violent or normal boost building.. it's an Australian product with Australian support (Ray knows his stuff) so can't go wrong. Very easy to hide, both the controller and the solenoid.

thanks guys

ill probably go the gizzmo.

ive read a lot about both

just wanted more opinions

Mate - Gizzmo MS-IBC for sure! It took me around 1 hour to hook it up and and around 15 min to tune it on the road - First time I had ever installed an ebc.

VERY easy to hide and imho is probably the BEST out there for the money you spend on it. The actual tuning process is MUCH easier then how it is in the PDF guide.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm firmly on the "zero compliance is good compliance" for FUCAs. I'd be looking to solid metal joints even if the primary reason for having them is because they facilitate the twist in the arm. I have never been more happy with the way the front suspension behaves than I have since I got rid of the FUCA bushes. Even the thin little (short lived) poly bushes in the Whiteline adjustables have too much compliance for my liking. It probably won't be long before I have sphericals nearly everywhere, probably including both top and bottom arms in the rear, and I'll start complaining about the increased costs for dental work. But I will be enjoying the driving more, I'm sure.
    • Plus, you'll get great experience in bedding in pads!
    • I have offset Nismo brackets so the fact the gktechs can pivot is less important to me. I have 170mm JIC arms with bushings - but they provide no adjustment and I'm not sure whiteline eccentric bushings will fit them (I don't want to ruin the bushings currently in them to find out). Ideally I want something with bushings + adjustment; hence why I'd like to find a pair of these. Unfortunately they aren't easy to find.
    • @Vee37 How much do you really care about finding these pads again? If your pads are quiet, work well and produce minimal dust, really isn't that enough? If you are set on finding the exact pads again, I suppose I'd do something like this -  Visit your local Jax, find out what brand of pads they carry. If the Jax workshop you previously went to had the pads on the shelf, then you can almost guarantee it will be of said brand.   I'm guessing you don't have the receipt for the previous work and pads. Can you visit a Jax workshop and see if they can look up your previous job to see what pads were fitted?  Still no luck? Put your stalker hat on, find the staff that used to work at the Jax store and ask them. Talk to local workshops, try to find out where the mechanics went to. Talk to Jax workshops, maybe they relocated to another workshop. When it comes to mechanics, its a small world. You'd be surprised how easy it is to track someone down. If these ideas don't work, shit will start getting crazy very quickly.... You could find out every brand and model of pad that fits that car... and try them individually ticking each off the list if it wasn't the one you were looking for.... If you go down this path your going to want to learn how to swap pads yourself, it is very easy, takes minimal tools and space. If you have room to park the car you have room to swap the pads. Plus you have the advantage of making sure all the brake hardware goes back in so they won't squeal! 
    • You miss spelled bearings...
×
×
  • Create New...