Jump to content
SAU Community

Buying An S15

Rolo Tummussey

By Rolo Tummussey,
in General Automotive Discussion

 Share

Recommended Posts

Rolo Tummussey Apprentice

Rolo Tummussey

Posted
Posted (edited)

I did a quick search around the internet and can find suprisingly little on the subject. Probably 'cause the silvia forum is down right now. I'm looking at buying an S15 (J-spec) and want to know about some basic modifications. The only info I can find is either from Gran Turismo doochebags who want 1000hp from a 2L whilst clearly not knowing basic mechanics like what a distributor is (to use an example) and Americans with American dollars at Mexican labour rates; I don't expect my dollar to go as far here.

Looking to spend as little as possible and begin with making about 300hp (if possible). Getting it to rev even more freely would be nice too. Can someone throw some figures at me? What could I do for $1,500, 2k, 3k etc.? Stuff that could be built on in the future would be best too. This way the end result in a year or two's time will be better. I have read that the stock engine runs at 11psi can be reliably boosted to 17psi without any attention to the internals and cooling. Is this true? To any extent?

On a side note, does anyone know exactly how much modification you can get away with when importing? I know it says it has to be factory and maintain the standard silhouette but most people seem to get away with little things and some quite a bit. I regretably passed up a newly imported silver car at a dealer a few months ago with full aftermarket suspension. Looked like there was a good 4/5k worth of gear there which the dealer said was installed in Japan before they bought it. Letting some Japanese guy pay for most of my performance modifications would be great if I could import one already done :)

Does anyone know about installing one of those stroke kits (increase to 2.2L)? Does it do anything spectacular to the performance? How much work is it to install them? I like to think I'm at least mildly mechanically minded but some labour costs for having someone else to install it would be great. Wouldn't want to blow my budget on the kit and figure out I can't do it myself.

Lastly, does anyone know anyone who does good, low cost custom decals (partially design/sketch my own and get 'em made up)? Not sure if I want to go down the full on exterior path yet but if I do, I want to do it right (not just a shopping list of the manufacturers of the parts I can't afford...).

I'm in Melbourne; if anyone could point me in the direction of a few speed shops I should talk to that'd be great.

Post Script: can't find much info on the actual install process of scissor doors; plenty of cheap kits though. Again, not sure if I want to go down this path, just food for thought. I know there's a long name for them but is there a 'street' name for the kind of doors on the McLaren F1 (kinda upwars and gullwing)? That's what I'd be after. I just can't find any info on how hard they are to install. Also read somewhere they're illegal but not sure which country the writer was in.

Edited by Rolo Tummussey
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      what stock throttle body to use when putting front facing intake on r34 gtt

      By Dose Pipe Sutututu · Posted

      might as well go e-throttle
    • Dose Pipe Sutututu
      AC Compressor

      By Dose Pipe Sutututu · Posted

      FWIW, I've always found Toyota A/Cs to be much colder than Nissan ones. Even that 2024 Nissan X-Trail (that VW Australia lent to me), the A/C isn't as cold as other base model Toyota Corollas/Camrys, etc. Maybe Toyota A/C compressors are superior? 
    • Rezz
      Photo Diary Comeback Special

      By Rezz · Posted

      Hurry while stocks last! 🤣 13% points redemption on this $6000 Mont Blanc "James Dean" ballpoint pen at Yodobashi Camera in Umeda, Osaka
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      It's not that at all....I just love the R chassis too much to keep racing it! Absolutely impossible to fix the damn thing if I bend it.... That last off I had (when I neglected to do what Kel said), we removed a gum tree with the side of the boot....needed a new rear quarter, boot lid, floor straighten, rear bar, front bar, both front guards, radiator, bov return and I still haven't got it back for a proper alignment to check it is actually straight again). There are just too many ways in tarmac rally to do significant damage to a car that you can't really get parts for.
    • Duncan
      Thanks Santa (the neverending trials of the 400,000klm, 400kw, RB30, manual swapped Stagea)

      By Duncan · Posted

      Now I'd said earlier I'd checked the fuses, and per @Stick180's suggestion I checked them all again. The check was to use the multimeter in continuity mode on the top of each fuse where the little metal tabs are available for that purpose. All good....except that very "A/T Control" fuse was actually blown when I pulled it out and looked at it. Put it back in, tested it again, there is continuity to both sides even though the fuse is blown. I'll need someone smarter than me, but my suspicion is that I was getting a circuit through a power supply, through an incandescent globe somewhere, to earth, to the shorted wire and back to the other side of the fuse, making it look like the fuse was OK when it wasn't....please anyone that understands this f**kery explain it to me. Bottom line....that suspicious purple/white wire, in an undamaged factory loom, that goes to the the wrong place in the fuse box has a dead short to earth, confirmed from both ends.  How a single wire in a factory loom can be shorted, especially the best protected loom in the whole car (underneath the top of the dash) is going to keep me awake at night because surely whatever caused the damage has (or will) damaged other wires in that loom too. So, to finish this long and sad story....cut the purple/white wire where it exits the fuse box, ran a new wire from there to the ECU loom pin 31, fired it up and drove happily into the sunset. Only 4 days of head scratching and peering into footwells to get me there. Another collection of wire removed (in addition to the earlier photo) and a bunch of 10a fuses that gave their lives for the trouble shooting....thank you for their service.  And, since the car was in the shed I resealed the cam cover (first time I've ever had a new seal leak on an RB, but the Stagea is that kind of lucky), and I put in the boost doc cam splash plates to try and turn down the blow by a bit while I was there. Which, was all good because it also let me find the slow coolant leak, turns out it was from the turbo water supply which I nipped up again (the banjo bolt got new washers, and I tightened the hose end and hose to banjo fitting while I was there)
×
×
  • Create New...