Jump to content
SAU Community

Recommended Posts

  • Replies 109
  • Created
  • Last Reply

Top Posters In This Topic

What "Class" shall i enter my car in? I'm going to be using street rubber.

I am thinking "Skyline Class", but don't want to hold up faster cars running semi slicks, with better drivers :(

Is my car too fast for "Novice"? I am not out for times, just to have a bit of fun.

"Expected lap time": Any help here would be great!

What "Class" shall i enter my car in? I'm going to be using street rubber.

I am thinking "Skyline Class", but don't want to hold up faster cars running semi slicks, with better drivers :(

Is my car too fast for "Novice"? I am not out for times, just to have a bit of fun.

"Expected lap time": Any help here would be great!

Al yes your in skyline class.

however they then split ppl into about 5 groups for the track depending on speed.

so last time myself (in the 200sx) and a R33 were on street tyres..(and lots less power than u) and were 1:42-1:46ish

if that helps at all?

M

you can generally move around the group a bit during the day, if your going much slower or much faster than the rest in the group.

the class doesnt mean much for us, its more for the wrx guys.

if your not out for times and just shits and giggles, then just email [email protected] and tell them.

ha i look forward to seeing your machine sideways out of the cleavage and onto the long track section :)

Hey all just to let you know I have updated the championship results..

It's close at the top in a few classes so make sure you come along and defend your honour!!

http://www.skylinesaustralia.com/forums/in...t&p=4840438

Enjoy!

Entered and paid! :(

How do i check whether the WRX club have recieved my form/money? IE: Is there an entry list?

Hey John, i'll probably disappoint you mate. I'm out to have a fun day, as i've already kissed a wall once, at the WRX track day, and the wall on the straight of Winton is farken close to the track. I'm also going to be running street rubber, so i'll be taking it a little more easier.

Entered and paid! :(

How do i check whether the WRX club have recieved my form/money? IE: Is there an entry list?

Hey John, i'll probably disappoint you mate. I'm out to have a fun day, as i've already kissed a wall once, at the WRX track day, and the wall on the straight of Winton is farken close to the track. I'm also going to be running street rubber, so i'll be taking it a little more easier.

http://www.wrx.com.au/forum/viewtopic.php?...4505179d74059c4

cheers

M

i would love to attend this one, however im doing the 6 hour up there the following weekend and as much as i love winton, i think two weeks in a row is a bit much...

anyone else from here doing the 6 hour?

Entered and paid! :D

How do i check whether the WRX club have recieved my form/money? IE: Is there an entry list?

Hey John, i'll probably disappoint you mate. I'm out to have a fun day, as i've already kissed a wall once, at the WRX track day, and the wall on the straight of Winton is farken close to the track. I'm also going to be running street rubber, so i'll be taking it a little more easier.

disappointment, from the rb30. never.

the back of the track is nice and open :D

lol last time i was a winton a r31 lost its left rear wheel (the whole wheel and studs). through the 's' onto the old front straight.

now that would have been a ride and a half.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
    • Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...