Jump to content
SAU Community

Recommended Posts

Well i've tried everything. Radiator professionally flushed and cleaned, new thermostat, water pump impellor perfect, changed fan over. And still the engine is overheating. The strange thing is that the fluid in the radiator is cool. Could there be a blockage somewhere in the water jacket?

Regards, Rob.

Link to comment
https://www.sau.com.au/forums/topic/288793-cooling-issues/
Share on other sites

once the car warms up .. is the top radiator hose hot ? It should be .. Is the bottom radiator hose only warm (not hot like the top one) ?? The bottom hose should only be warm if it's hot then your radiator is not doing its job

The factory water temperature sensor is at the top radiator hose (water exiting the engine) so if it's reporting the engine is overheating the top hose should be HOT which is normal ..

You could also have air stuck in the cooling system so bleed it ... best way to do it, 2l coke bottle shove it into the radiator cap seal the joint so coolant doesnt leak and then poor coolant into bottle (obviously cut the bottom of the bottle off) let it run for about 30 mins ..all the air will come out the radiator cap and you will see big ass bubbles in the bottle with the coolant

Link to comment
https://www.sau.com.au/forums/topic/288793-cooling-issues/#findComment-4837355
Share on other sites

you have said that the water pump impellor is perfect, but how is the housing? if the housing is a bit worn and the impellor isn't making a tight seal then it won't pump any (or enough) to cool the system properly (had this problem with my outboard. the impellor was new but it wasn't pumping water at idle and only a little bit at full speed because of the housing being worn). if you don't know how old the water pump is then i would replace it to be safe.

also, when the radiator was professionally fluched/cleaned, did they actually open it up and clean it, or just flush it?

for the fluid in the radiator to be cool while the car overheats means that there is a flow issue, whether it be the thermostat not opening properly (you didn't install it the wrong way did you?), the water pump or a blockage or air leak.

as wacky dee said, the top hose should be hot. if it isn't and you are still getting overheating issues then there are a few things to do. first (this only applies if you have a stock ecu and are going off the temp gauge in the dash saying the car is overheating) is to get a hold of a consult cable so you can see what the ecu is reading the temp as. it reads from a different temp sender to the dash, so if it is reading ok then you just have a faulty temp sender. however if it is reading hot as well as the dash but the coolant/hose is still cool, then i'd say the thermostat is a probable suspect as it will be letting out a very small amount of coolant (enough to alter the temp sensor reading) but not enough to actually heat up the radiator

Link to comment
https://www.sau.com.au/forums/topic/288793-cooling-issues/#findComment-4837918
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For your application, where you'll be at that 1/2" size or perhaps larger, yeah, excellent. Although not if you need a tight bending radius anywhere, because the corrugated stuff is not anywhere near as flexible as rubber/teflon cored stuff. But for turbo oil lines? No. Too big. They just don't do the corro stuff down at the ~1/4" ID size that you'd want, and if they did the OD of it would probably be a bit too fat for fitting it into the tight spaces available. I use hoses like that all the time for fuel gases (LPG, NG) and liquid fuels (HFO, diesels, waste oils). When we did the London Olympic cauldron, with the 204 individual burners on it, we had miles of the stuff (although a lot of that was teflon core). A bunch of that crap is still cluttering up the workshop, more than 12 years later!
    • Would something like this be an option  https://processhose.com/products/configurable-metal-hoses/1-2-in-t316-stainless-steel-annular-corrugated-configurable-flexible-metal-hose-assembly-with-ends-t304-single-braid-masterflex-af5550.html I'm looking at this for replacing the OEM EGR when installing a aftermarket intake plenum 
    • The once piece tail shafts with cv type joints on either end are the ones that end up vibrating and the vibration is caused by the cv joint binding as it turns, I’ve also seen them explode from the binding 
    • Take this with a pinch of salt, it's from someone (me) who got annoyed with turbos entirely. I hated aftermarket lines. If I had the option to use hardlines with whatever turbo I had - I would use them, 10/10, 100% of the time. The only reason people go larger, heat resistent, shielded lines etc is because they have to. And yes they don't last forever. Even if you spend big bucks on all the best heat shielding money can buy, with the best heat resistant, fuel resistant, oil resistant, radiation resistant hose, they get stiff and break down and just don't last the way a metal pipe will.
    • Unfortunately I am quite literally halfway across the globe. So all sources for parts like that are far away for me. What do you mean by that exactly?
×
×
  • Create New...