Jump to content
SAU Community

Puting A 26/30 In A R32 Gtst And Dont No Wat Engine Mounts/brackets To Use

4dr wannaslide

By 4dr wannaslide,
in Engines & Forced Induction

 Share

Recommended Posts

4dr wannaslide Community Regular

4dr wannaslide

Posted
Posted

well its a r32 4dr rwd and im put a rb26/30 and want to know wat engine mounts and brackets to use or mods to do fit it under my gtr bonnet, cause they sit so much higher,, dont want to change the bonnet at all. cheers liam

shanef Grand Master

shanef

Posted
Posted

Didi you actually read any of the 600 threads that have this info in them before you decided to post a new topic?

I suggets u atleast search in the sticky at the top of this section.

brada31ke70 Enthusiast

brada31ke70

Posted
Posted (edited)

yes, a 26/30 will clear the bonnet with rb20 or rb30 engine mounts. i am the same as you, dont have that much time to use the computer and it is much easier just to ask than going through all the threads. others cocks could have answered your question in the time that they wrote up their answer about looking in the sticky. ask as many questions as you want, it is how you learn and save time, those others probably only know the answers by studing forums rather than actually doing the work themselves, freedom of speech mother lickers. hahah, cant wait for the reply to that one. good luck with your build 4dr wannaslide.

Edited by brada31ke70
MBS206 Grand Master

MBS206

Posted
Posted
Please don't generalise.

I reckon... Don't know how many times I've lost skin from swapping engines... Oh wait... I'm missing a heap of skin down the side of one finger from swapping one RB25/30 for another RB25/30...

Use the SEARCH!

  • 3 weeks later...
Craved Grand Master

Craved

Posted
Posted

lol @ this thread

seriously - if you are on 40 posts per page its on the LAST page of the sticky if not, the 2nd last page - 1st post with pictures from sydneykid

http://www.skylinesaustralia.com/forums/R3...&start=6920

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Potential MAP Reference Point

      By GTSBoy · Posted

      Getting a decent signal from all 6 throats is a challenge. I don't know for sure, but I suspect that the stock balance tube is not ideal for it. I have done it on an ALFA 4 cylinder (about 35 years ago, so don't ask for too many details). We drilled 4x holes in the manifold runners, put in some fittings and ran hoses to a decent sized (I think it was about 20mm diameter) pipe that ran the length of the inlet manifold. So, it was quite a decent volume. There is a "tuning" balance to be found between the volume of the common plenum on such a thing and the diameter of the pipes running from it to the runners. You need the volume to be large enough to damp out the sharp spikes in pressure signal you get as each runner gets sucked on by its cylinder, but not so large that it becomes too slow to respond to actual changes in MAP. And you need the hoses to be small enough to transmit the signal quickly, but not so small that they delay the signal. You might have to have more than one go at it, if there isn't any actual success based wisdom to be had here. Hopefully there is. Anyway, I would not do it on only a couple of cylinders. I would also not care about "permanently modifying a part". Just bloody drill holes and make stuff better. There is nothing sacred about any GTR unless it is a genuine museum piece that you shouldn't be modifying at all anyway.
    • MBS206
      NC MX5

      By MBS206 · Posted

      He's still joining you, he's just delayed it and won't have the fulleh sick ITBs...
    • Kinkstaah
      R34 GTT front hood lip

      By Kinkstaah · Posted

      The strange thing is this is a URAS front bumper (or clone of it). The bumper actually does not sit flush with the GTT hood - You need the addon to make the hood 'long' enough to reach the bumper. I have no idea why they didn't incorporate this piece into the bumper itself.. instead of sticking it to the hood instead.
    • AdiR34
      R34 GTT front hood lip

      By AdiR34 · Posted

      Another thought on this OLD topic: When you paint your bonnet lip, leave a small unpainted back lip/line along the back of the lip, where it rests on the bumper. That way, the line in the back is much more prominent than the gaps in the front/under the lip - and it breaks the hood-to-bumper connection at the "correct" place, when comparing to a GTR. I'm gonna do this with mine this week, so stay tuned for pics!
    • Radical_Goodspeed
      Potential MAP Reference Point

      By Radical_Goodspeed · Posted

      So I'm in the final stages of assembling my single turbo RB30/26 and had a question regarding MAP reference points.  I've seen several recommendations such as tapping the cylinder 2/3 ITB, tapping the intake manifold at cylinder 2/3, or using a point on IAC. First two are doable but require permanently modify part and the third is "out" as I plan to delete the IAC.  All that to say my question is can I used the "bleeder" in the center of the ballance tube as a MAP Reference? I'm running a catch can so I don't need it for the PCV system. My thought process is it "pulls" from all 6 cylinder, and it's between the ITB and the cylinders making it ideal for MAP reference according to what I can find. Thoughts?
×
×
  • Create New...