Jump to content
SAU Community

Fs: Fuji Fronter 350 Minilab, Fuji Dpc, Konica Film Developer, Fuji Imaging Station, Epson 1680 Pro Scanner

Dose Pipe Sutututu

By Dose Pipe Sutututu,
in For Sale (Other Items)

 Share

Recommended Posts

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

Hi there,

My uncle shop, which I manage on the weekends and part-time whilst I was at uni a few years ago is closing down. Rent hike & low turn over doesn't help.

R31Nismod, I'm not selling for someone, I actually work here too and setup the entire network

Up for sale, and is still running, we were told our lease ends 18th October, 2009.

- Fuji Film Frontier 350, probably has under 2 million prints, quite a low count (has been to converted to external chemical tanks, larger capacity than chemical packs)

- 3x Fuji Film DPC Centres (Touch Screen Photo Selector), using Whitech Photo.Teller Software

- Konica Film Developer

- Imagining Station, Had Adobe 7, Fronter Imaging, Epson 1680 Expressions Photo Scanner

- All Manuals

- Spares

- Spare heaters, rollers, heater rack

- 4x 6" inch magazines

- 1x10" inch magazine

- 1x8" inch magazine

- Parts to change the size of the magazine

Asking for $35k for the lot, which is cheap as chips... ex leased Rabbit Photo Frontier minilabs go for around $50k and they're thrashed with heaps of prints and doesn't come with the extras

Still in running order, come inspect it at Shop 17, Bonnyrigg Plaza, Bonnyrigg, NSW, 2177

Contact: PM me or e-mail me on johnny_t_la AT hotmail DOT COM or call Tan on 9610 7699

Location: Bonnyrigg, NSW 2177

Price: $35k ono

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
  • Author
Posted

Price drop to $25k, one less magazine, now only 5x Magazines.

Comes with a 1x APS, 1x35mm, 1x Manual Mask, All film carriers from 120mm to 110mm to square film shet..

Frontier%20350%2001.jpg

Frontier%20350%2002.jpg

Frontier%20350%2003.jpg

Frontier%20350%2004.jpg

Frontier%20350%2005.jpg

Frontier%20350%2006.jpg

Frontier%20350%2007.jpg

Frontier%20350%2008.jpg

Frontier%20350%2009.jpg

Frontier%20350%2010.jpg

Frontier%20350%2011.jpg

DPC%2001.jpg

DPC%2003.jpg

Photolab%2001.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      R34 Gtt Wheel Offset Advice

      By GTSBoy · Posted

      What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • silviaz
      R34 GTT idle problem

      By silviaz · Posted

      I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • Kinkstaah
      R34 Gtt Wheel Offset Advice

      By Kinkstaah · Posted

      This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • AdiR34
      R34 Gtt Wheel Offset Advice

      By AdiR34 · Posted

      Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...