Jump to content
SAU Community

Z32 Afm, Cusco Upper Arms, Fuel Pressure Reg, Blitz Bov

toygtr
 Share

Recommended Posts

toygtr Community Regular

toygtr

Posted
Posted

Cleaning out my shed. All parts are off my R32 GTR.

All worked fine and are in good condition.

Prefer pick up from MELB.

Nismo Fuel Pressure Regulator. $100

Z32 AFM $ 100

Blitz BOV $60

Cusco Upper arms $100

RB26DETT Cam Gears $ 40 both

Remapped ECU. $100

(Suits Z32 AFM, 550cc injectors, used to rev to 9000 rpm)

post-24510-1253875949_thumb.jpg

post-24510-1253876090_thumb.jpg

post-24510-1253876212_thumb.jpg

post-24510-1253876281_thumb.jpg

post-24510-1253876367_thumb.jpg

post-24510-1253876448_thumb.jpg

post-24510-1253876569_thumb.jpg

post-24510-1253876636_thumb.jpg

post-24510-1253876722_thumb.jpg

post-24510-1253876794_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Rb26 iron block limit

      By GTSBoy · Posted

      Yeah. OK. I'll say the same thing I say to everyone. You do not have to use 100% throttle all the time.
    • niZmO_Man
      ATCC Amaroo Park 1987

      By niZmO_Man · Posted

      R31 = nose heavy
    • Curlyfred
      Rb26 iron block limit

      By Curlyfred · Posted

      Mainly being afraid of breaking something on something i've poured so much money into haha
    • Dylannn
      For Sale Haltech Elite Plug n Play

      By Dylannn · Posted

      Hey   ive gone for a terminated harness on my build so selling brand new unused and unopened piggy back harness  https://www.haltech.com/product/ht-141357-elite-2000-2500-nissan-skyline-r32-33-r34-gt-r/ Located Bathurst NSW   price $600 + postage     
    • drifter17a
      Rb25 trigger kit and timing misalignment

      By drifter17a · Posted

      The trigger kit I have is similar to the one in the link below. While going through Facebook, I saw someone else mention a similar issue, and I’m starting to think this could be related to the crank gear itself. I understand these parts are CNC machined, but maybe some earlier versions or individual pieces might have slight inconsistencies—it just doesn’t look right in my case. https://www.facebook.com/share/16an8evZd9/?mibextid=wwXIfr I originally installed the crank gear using the thin OEM washer, but as shown in the attached photo, the timing belt walks very close to the edge. When I tried using a Nitto washer—which is thicker—it actually made the issue worse. The belt walks about 1mm off the front edge, which raises more concern about alignment.   I’ve gone through the full process of elimination:   The tensioner pulley and bolt are brand new and installed correctly. The bolt isn’t bent and is oriented properly. The back of the tensioner and the idler pulley are clean and seated correctly. The idler sits slightly more forward, which I understand is due to its design. I’ve experimented with both tight and loose belt tension, but it makes no difference. As soon as the engine runs, the belt immediately walks forward again—even if I reset it beforehand.     At this point, I’m considering replacing the crank gear with your Race Version 1 (12-tooth), but before purchasing, I wanted to ask:   Are you aware of any alignment issues when using this gear? Would this gear help keep the belt aligned correctly, or could the walking still occur? Does it work with a standard missing-tooth crank and rear washer? Is there any specific crank setup or install procedure required?     For reference, I’m not using a front washer, as the PRP crank gear seems to replace the need for one.   Looking forward to your advice.
×
×
  • Create New...