Jump to content
SAU Community

Jacking Up Ur Car

kikutaknight

By kikutaknight,
in WA Wasteland

 Share

Recommended Posts

kikutaknight Enthusiast

kikutaknight

Posted
Posted

I've seen pictures of people with their cars jacked up two wheels at a time with the jack somewhere in the middle...

also cars jacked up from somewhere other than that little bit on the side made for those dodgey little car jacks.

i've looked around on the bottom of my car but can't figure out exactly where people are putting these jacks. can anyone upload pictures or something for me? :D 

would be appreciated...zorz.

Link to comment
https://www.sau.com.au/forums/topic/289799-jacking-up-ur-car/
Share on other sites
260tech Proficient

260tech

Posted
Posted
I've seen pictures of people with their cars jacked up two wheels at a time with the jack somewhere in the middle...

also cars jacked up from somewhere other than that little bit on the side made for those dodgey little car jacks.

i've looked around on the bottom of my car but can't figure out exactly where people are putting these jacks. can anyone upload pictures or something for me? :P 

would be appreciated...zorz.

Check out this thread. http://www.ehow.com/video_4941952_put-jack...er-vehicle.html

Stay safe.

GW

Stinky Rooster Grand Master

Stinky Rooster

Posted
Posted

That vid misses quite a few vital safety aspects, like making sure the non-raised wheels are chocked properly for one...

Firstly, never ever ever try and use a sill jack on any other part of the car other than the proper jacking points. As Bard said, a road car is not strong enough to do this and you will either destroy the jack or your car. Heck, if your lucky, maybe even both!

If you want the front lifted then use the centre of the cross member - not the sump! Always use jack stands and try to keep them as close to the suspension pick up points as practicle as possible. The control arms used in that vid are a good idea, although I cant say using the edge of them is that bright. Personally I would use a bit of wood between the jack stand and the control arm (steel on steel is asking for trouble IMO) then you can use the whole control arm not just the edge.

For the rear, try putting the jack under the diff housing. Just be aware that the car will be VERY unstable as it is being jacked and can rock from side to side.

It should go without saying that safety should always come first. Never get under a car that is supported by a jack, always make sure the car is on level ground before raising it at all, and try to keep bystanders right the f**k away. One other person as a spotter is a good idea, but that should be it. Always fully chock any wheels that are to remain on the ground. Also, try not to open any doors on a car that is supported by a jack. Especially on 2 door cars, this can really upset the balance of the vehicle. Lastly, as I said before, its always a good idea to use wood between any steel jack or jack stands and the car. Apart from adding a "crush" factor that helps with stability, the friction coefficient is much higher making it more stable.

  • 3 weeks later...
  • 1 month later...
08yannch Rising Star

08yannch

Posted
Posted

+3 for the diff or x-member/rad support :laugh:

also i use the OEM jack on one of the sides so if a stand does fail the car wont fall all the way 2 the ground.

also never use bricks 2 suport a car i made that mistake once and i will never do that again :)

JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

spare wheels and tyres are really good for getting a car up off the ground, if your doing something that doesnt require removing any of the wheels you can simply jack it up via the diff/xmember and chuck a spare wheel and tyre under each wheel, 2 if you need to go really high. if the wheels need to come off you can put the wheels and tyres under the chassis rails, make sure you have the car sitting on 4 points before you get under there and dont have the front supports too far back, the motor is the heaviest part.

08yannch Rising Star

08yannch

Posted
Posted

car ramps are good 4 doing work on a car when u don't need 2 take off the wheels and also there is no ramp solution 4 raising the whole car unless u make some.

4 me im restricted when it comes 2 space so im stuck with a trolly jack and axle stands (modified 4 skyline)

08yannch Rising Star

08yannch

Posted
Posted
with the height of the average skyline ramps would need to be about 8 feet long to be much good to ya

unless you remove the front bar or something????????

well all u do is wedge a thick bit of wood in there to extend the length

 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • kike_kike
      Problem with a tachometer on a Skyline R33 with an RB25DET Neo engine

      By kike_kike · Posted

      Hello First, I apologize if this is not the correct forum. Let me know and I will move it to the correct one. I'm having a problem with the tachometer on my Skyline R33 with an RB25DET Neo engine. I'll tell you from the beginning. I'll tell you from the beginning. I have the RB25DET Neo engine installed in a Nissan Patrol GU, with a Link G4X control unit specifically for that engine,  and I have fitted a Skyline R33 tachograph to the original GU dashboard, but it doesn't work properly. I have the tachometer connected to the positive and negative terminals of the GU panel's wiring, and the signal cable is connected directly to the ECU output pin, but the rpm fluctuates widely. Can anyone tell me if the output signal from an R33 ECU is the same as the output signal from an R34 ECU, or if the voltage and signal type are different? Regards and thanks.  
    • Hexi
      Dumb rich kid tries modding for the first time

      By Hexi · Posted

      I guess it was the thought about "Oh if I were to drive this everyday". Then no, SL500 I wouldn't really consider lmao. 
    • Hexi
      Dumb rich kid tries modding for the first time

      By Hexi · Posted

      Yeah actually really fair point. Idk what I was thinking when looking at the SL500. Now that I think about it, I feel like I would have more enjoyment out of a shitbox that I would need to repair than some fancy merc. Although I must admit the SL500 does look quite nice. My bad hahaha.
    • Kinkstaah
      Dumb rich kid tries modding for the first time

      By Kinkstaah · Posted

      100% Also "Not wanting to spend money" is THE WORST IDEA IMAGINABLE when coming to a project car of any kind. They EXIST to BURN MONEY. Sure, gas money is a thing. A stock car with the worst fuel economy ever sold would probably be cheaper than modifying a car with FREE petrol for the life of your ownership of it, lol.
    • MBS206
      Dumb rich kid tries modding for the first time

      By MBS206 · Posted

      Amount of time you're being observed by law enforcement is so minute, that you could be a dumb shit 90% of your driving time, and never lose a demerit. You could also be the best driver ever and still get hit with a fine.   When you realise how quickly everything turns from "Wee, we're having fun!" To "oh f**k oh f**k oh f**k", you start to realise the only way to be a good driver, is to not be doing anything dumb or unexpected by normies on the road. You want to go fast, go to the track. Someone there in a 1990s slow POS will also show you how bad of a driver you are as they lap 10 seconds per lap quicker than you can in a car that should be considerably faster.
×
×
  • Create New...