Jump to content
SAU Community

Scr48 First + Only!


Recommended Posts

Did you change any of the fuel lines at all as I got told E85 will eventually corrode the factory lines and sender unit

Some lines have been changed yes

Link to comment
Share on other sites

Just looking at converting to E85 is all thought I'd ask a few questions on the conversion

It's definitely worth making the switch. Too many easy gains from it not to and it's becoming more and more readily available

Link to comment
Share on other sites

Gee where to start, Needless to say the last week has been pretty full on.

After many a delay I finally got the car back on Friday. After noticing the car was on the dyno at 10:30am on Friday I expected to get a call around 12:30pm-1pm stating that its done. It came to 3:30pm and I hadn't heard anything so I gave them a call. Apparently the car ran out of fuel on the dyno during tuning and they had to go get some more (I dropped it off with a full tank). I let them know it takes me 2 hours to get there so if they know when it will be ready i can start heading there earlier so they arent hanging around waiting for me all arfternoon. Finally got a call back at 5:30pm stating that its nearly finished and to head down.

They advised on the phone that it made 630rwhp on 29psi, however the head was lifting and they wanted to "dial it back" a bit to make it safe for powerplay.

Arrived there at about 7pm and got chatting about the car. Even though the car has ARP head studs it was still lifting. I thought "righto at that pressure I guess it needs looking at". Then came the "Dialed Back" numbers. They ended up bringing it all the way back to 451rwhp on 15psi. I still and even now am surprised they had to drop it back so much to make it run safely. Due to the time of night and a bit of disbelief on my behalf I didnt go into depth about the lifting issue etc.

By the time we got the car loaded onto my mates tow truck and got it back home & back into the shed it was 11pm. After finishing off other setup jobs for powerplay the next day I got to bed at 12:30am.

NOTE : I DO have dyno sheets for both the 630 runs and the 451 runs. I will scan and upload them hopefully tonight.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The two diagrams are equivalent. The R32 one is just one sheet out of about 3 showing everything in the whole car all at once. And without knowing the functionality that occurs in the modules, they are both equally opaque.
    • 8v - 2.48ms 9v - 2.15ms 10v - 1.74ms 11v - 1.41ms 12v - 1.15ms 13v - 0.99ms 14v - 0.89ms 15v - 0.82ms 16v - 0.81ms I'm running these values on my RB20 Neo with 570cc Denso R35 stock jets and it's great. Also bought a set for my Legnum VR4, love these injectors!
    • Thanks for your reply,  Those blue/green wires running to the actuator aren't attached to anything, so I'm not sure how the central locking is still working. I will have to take a good look tomorrow, I don't have the car with me. After googling it seems like a pretty common aftermarket actuator which even uses the same green/blue wires the immobiliser required. i'll test everything tomorrow and if it's working i'll melt the solder, strip it, resolder and neaten it all up with some heat shrink. I don't have to understand it if it works hahaha I just don't want a fire/ short circuit. That R32 diagram looks more like a continuity chart? Can you make sense of this form the R34 manual? 10V is probably due to very flat battery, i'll recheck as well tomorrow, I did have to jump start it haha. Thanks again!  
    • So, COM doesn't mean comms. It means common. What common itself means will depend on the type of device. For a two directional actuator (ie, one that can push and pull on the same output rod) then the common will typically just be the earth connection. There will be at least 2 other wires. If you put 12V on one of the other wires, then the actuator will push. On the other 12V wire, it will pull. Can't quite make out what is going on with the wiring of your actuator. It appears to have several wires at the actuator plug, but there only appears to be 2 wires where its loom approaches the door control module, with at least one of the others cut off. I don't know these actuators off by heart. I'd have to look at a wiring diagram for one before knowing what the wires were about, and that's despite me having to replace one in my car not all that long ago. Just not interesting enough to have dedicated memory set aside for trivia like that any more. That actuator is an aftermarket one, not the original one, which probably died and was replaced. That might require some sort of bodge job on wiring to make it work. Although nothing should justify the bodginess of the bodge job done. As to the soldering job on the door module's loom plug. Ahhahhahaha. Yes, very nasty. Again, I cant tell you what any of those wires do. You'd need to study the R34 wiring diagram (if you can find one that shows the door module). I don't think I have any. I'd have to study the R32 diagram to start to understand what mine is doing, and again, even though I've had a problem with mine for the last 25 years (where it locks the passenger door when the driver's window reaches top or bottom of travel) I'm just not interested enough to try to to work it out. So long as it's not burning down, it's fine with me. Here's the R32 GTR diagram, which, confusingly, has rear door lock actuators and window motors on it!! As you can see, unless you understand the functions of the door lock timer and the power window amplifier, you'll never be able to work out how it works just from the diagram. I don't imagine that the R34 one is any better. Hopefully an R34 aware bod can help. FWIW, the two wires that are cut and joined look like they are both power supply - so hopefully it is not fatal to join them. The 10V you measured on the cut off free end of one of them is concerning. You'd expect 12V, and it might be the reason for the bodge job joining them together.
×
×
  • Create New...