Jump to content
SAU Community

Recommended Posts

I have a 1993 r33 s1 gtst for sale was my project for track/drift car.

Motor is an rb26 with gtst gearbox. engine was fully rebuilt from sep 08 through till January done around 3000 km since. The rb26 is out of a r32 gtr but has the r33 crank for the longer snout for oil pump drive.Rebuild included forged pistons and rods, arp head studs, new n1 oil and water pump, ACL racing Bearings. block was decked and machined. head was fully serviced machined and valves reseated. Bottom end ballanced metal head gasket. Recipts for work done.

car has coilovers, big y pipe, walllbro 500hp fuel pump i think it is. SARD fuel reg. gtr dash.

Has standard turbos. body is Straight but needs attention

$7500 FIRM as it sits has out of rego sep 23. 2009 pink slip on 20.9.09 still has few weeks left

can be contacted on 0411672105

post-52687-1254466303_thumb.jpg

post-52687-1254466400_thumb.jpg

post-52687-1254466435_thumb.jpg

post-52687-1254466490_thumb.jpg

post-52687-1254466533_thumb.jpg

post-52687-1254466598_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/290330-r33-gtst-rb-26-built-motor/
Share on other sites

Hey mate, couple of questions for ya.

1) Is it engineered for the RB26?

2) If not, is the RB26 engine number on the rego papers?

3) Does the car have any mechanical faults whatsoever?

4) Will it pass rego with a new front bar?

5) Receipts for engine build? (Sorry, just re-read and says you do)

Cheers mate.

Edited by XS80ST

The engine numbers off the 26 are on the rego papers but no engineer cert wasnt required. car has CURRENT PINK SLIP just need to pay the rego

hey just FYI you dont need engineering to stick a rb26 into a r33 gtst. I built one and when it came time to register they couldnt have cared less. - hope this helps with your sale if it was in perth i would have bought it by now too :(

hey just FYI you dont need engineering to stick a rb26 into a r33 gtst. I built one and when it came time to register they couldnt have cared less. - hope this helps with your sale if it was in perth i would have bought it by now too :(

yer it is regoed with the 26 in it insurance didnt mind as long as it was on the papers. its killing my not getting a hit on the car at this price rebuilt cost me total around 8k and brought the car for 13k just befor the rebuild

front bars in the bin lol was big low fibaglass bar and got all cracked from bush driveway. i havnt had and accidents but passanger side was in under coat when i broght it guy i got it off said it was scraped car is pretty straight. had different front fenders on the car thats why they are different colour. will throw in fibagrass wide front fenders

hey.. just a few questions..

what engine management is the car running?

internal or external fuel pump?

any problems with the interior?

Cheers,

Corey

Edited by sIIgtst
Sorry guys hour north of sydney. Central Coast. if anyones keen on just motor or parts let me know

hey mate, where abouts on the coast are you? im at the entrance. id be interested in just the engine maybe as i need to rebuild mine so this would be perfect for me

Sorry mate no swaps. $12,500 and its yours lol. Car is geniune, im just after a quick sale. Need $$$ and people just want to negotiate prices.

too cheap! put the price up , then it will sell :rant: . i didn't read your advert properly but i'm assuming no swaps?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A little more work this week.  Fitted astra power steering pump in the boot with a lowe fabrication bracket. Gave the pump a good clean, fitted Anderson plug and high pressure fitting. With the intercooler being flipped under rad support factory headlights weren't going to work. Ordered a set of origin battle lights, they arrived so got them test fitted. Will require some fiddling to fit nice but was an easy quick option for now. And today we pulled out the manual Rb gearbox and test fitted a ZF 8HP50. It will fit with some casting tabs cut off and small tap of the tunnel with a hammer. Pick up the adapter plate Wednesday so hopefully all bolted in Friday and measure for tailshaft which will be a 2 piece. Been doing a lot of ecu, pdm and tcu loom design so when comes to wiring it in a few weeks will all go smoothly.
    • FYP. Sadly. Even bolt cutters wouldn't take 2 sec. But in the days of 18v angle grinders, nothing is safe.
    • One piece driveshaft I would recommend a dual CV setup otherwise stick to OEM. I have heard most one piece driveshafts cause excess vibration otherwise. The transmission grind I'm quite familiar with. You can try shockproof gear oil, otherwise you need a new transmission. The shifter is extremely simple on these cars. If you want pull apart the assembly and replace the plastic bushing but I doubt that fixes anything. The tail light issue is very common, unfortunately new tail lights are long discontinued. The trunk antenna going up always is because your radio doesn't have a true power antenna control, just remote amp power signal. There is a blank switch plate that you can pop out and install a switch for this or alternatively source a head unit that has proper antenna control. Throttle body sticking you have to disambiguate by disconnecting the cable and seeing if the linkages are the problem or something else. There is a procedure to adjust them, refreshing them is also somewhat involved if that's the issue. I have dealt with many of these issues. Old cars really are fractals of problems. The more you fix the more you discover there is to fix.
    • Welp, you've got a long list of experiences right there. I'd say you're on the right path.
    • That's correct, suits my requirements a bit better. Sure there are also numpties there, however it's generally a different vibe and more my kind of vibe.
×
×
  • Create New...