Jump to content
SAU Community

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

hey Steve, on my 34 the car misses on idle when the gap is 0.8 with the copper plugs .. 1.0 gap and no worries.

Hamish, I actually WANT to use a 1.1 gap for better combustion/power/fuel eco .. :P One of the reasons I got the splitfires.

most people gap to 0.8 with splitfires anyway....

TBH it might work @ 1.1 but with that plenum in the way i aint gonna bother to find out :P

heat range 7 seems to be the go too for 200+rwkw stenve... although 6 is quite popular and works on many a gtt/gtst

did it miss instantly? or could you have fouled them?

I've had heat range 6 and 7 in my 190rwkw R34 .. 7's give a slightly better fuel eco I think but apart from that they're both about the same. Unigroup were encouraging me to stick with 7s at this power level and I think they know what they are talking about. I'd give the 6s a miss unless your skyline is completely stock.

Johnny which ones are you talking about, the BCPR7ES-11's ?

found the BCPR7ES-11's at local repco just down the road .. woops, shoulda checked there first :whistling: $31 for 6, all goodah

Told you so :D

They're quite easy to get a hand on!

From memory it appeared to miss instantly (well about 30seconds or so after i started it), but i cant be sure. car isn't tuned yet so its possible i fouled them. (could be a loose loom connection, badly seated coilpack etc, bit of dirt or something as well)

I thought about gapping them back up to 1.0mm, but its odd that it didn't miss with the 7 heat range plugs at a 0.7mm gap :S i was under the impression the smaller the gap the worse the idle?

just called the local repco and ordered in the BCPR7ES-11's for me.

so tomorrow i'll throw them in at a 0.8mm gap i guess? what do you guys reckon? (running splitfires)

dont really feel like taking them in and out if it doesn't work haha. is it better to run them at 1.1mm gap if i can?

tony (munkyboy) runs the 7's at 1.1mm (i think) and he hasn't had an issue, but he has only just gotten some yellow jacket coils or whatever they are called

yeah 1.1mm with new coilpacks. but thats only at 13psi. i think i'll be going to 0.9mm for 16-18psi, and hope it holds up on the dyno.

looks like ive joined the 1.1mm club

just finished up and took it for a spin.

put it the bcpr7es-11's checked all the gaps, they were at 1.1mm then didn't touch them

took out the bcpr6es put in new plugs carefully hooked everything up and tada!

no more miss at idle, car seems to pull a lot easier, seemed a bit more powerful (probs just cause i was breaking traction on the wet roads all the time haha)

im running 12psi max. usually peaks about 11.5psi and no sign of a miss anywhere.

so there ya go if you are running splitfires at max 12psi, in "theory" you should be able to run 1.1mm gaps

how'd you go wacky dee?

just waiting for my splitfires to arrive and a date with unigroup ... I'm gonna do the same as you (same boost as well..11.5psi sometimes 12max depending on weather I guess) Good to hear you're not having any issues.

What did you use to check the gap on the new plugs? I checked with repco and they had those feelers but max .8mm or so (5 different kinds all maxed out at under 1mm)

lol. you add the different thicknesses together to make the amount you want. ie. 0.8 with a 0.3 or as close as you can. put them together, and check the gap.

yeah, what he said.

Dont worry i looked at it for a minute and went "wtf?"

Has anyone had issues with 7's fouling for normal street use?

I run BKR6E at 1.1mm on street (95%) and 7's at .9mm when it gets the boot in - 250rwkw+. I have remote mounted coils so swapping out plugs is a 5 minute job.

Is the OEM plug the same height as the BCP or the BKR? Maybe the BCP are actually too tall and put stress on the coils?

well im having the same issue as Stenve.....put in bcpr6es gapped to .8mm and now it misses.....at the start it would only miss when it warmed up...but now it misses from the time i start the car....

i have a little over 200kw s2 r33....have jjr coils....should i be running bigger or smaller gap??? and should I be using the 7???

thanks!!

6s will do the job ..but 7s are probably better for > 200rwkw and put the gap back up to .9 or 1mm and you should be ok. If that doesn't fix it, one or more of your jjr coils are dodgy.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...