Jump to content
SAU Community

Recommended Posts

i reckon its still possible to do it with the neo intake plenumn..coolant temp sensor can be swapped.. aac valves still operate as a 12V solenoid. throttle body can be swapped for an R33 one. etc

Edited by Simon-S14

i reckon its still possible to do it with the neo intake plenumn..coolant temp sensor can be swapped.. aac valves still operate as a 12V solenoid. throttle body can be swapped for an R33 one. etc

Yeah if you swapped the TPS you could do it, more the plumbing I was concerned about, not sure how different everything shapes up, lengths etc. Would need to change the injector loom though as the plugs are no doubt different.

Edited by Rolls

I am using all R32 loom up to the ignitor, I chopped the old plug off and used the R34 coils that have the ignitor built in and wired a nice new deutsch plug on the end removing the ignitor, plug looks better than factory! about $35 for all the pins etc but I know it will last forever now.

Using rb20det R32 ecu with a nistune module, R34 cas rewired (pin out is different) 1-4 2-3 3-4 4-1, Z32 afm and S1 r33 intake manifold with aux air valve, throttle body, tps etc. Basically looks like S1 rb25det everything with r34 coils.

Try and get a complete R33 intake/fuel setup etc as the r34 sensors etc are all different, different coolant lines etc, different fuel rail and injector loom, so have no idea how it would all mount up.

Cheers for the cas info rolls...

If I get there.. I'll be using the whole rb20 loom and ign, re-wiring the cas plug and adapting the mechanicals/sensors to the new manifolds.

If the 25/30 slapper fails I just built, I'll get a stagea neo.

absolutly! the best part of modded knuckles is the reduction of ackerman which means u can travel at angle, faster, as the front tyres aren't scrubbing out

It still looks pretty wrong in still shots!!! :nyaanyaa: It looks like the suspension has failed LOL

But i bet it makes a hell of a difference when sliding, not that you needed any help :thumbsup:

Just read all 22 pages, awesome build mate, reading this makes me want to get started on mine sooner. Good stuff!

So how did the gtx go compared to the non gtx?

Also whats the reason for the r33 TB instead of the r34 one?

Good work mate! :cheers:

Edited by phat_man

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
×
×
  • Create New...