Jump to content
SAU Community

Bride Maxis Iii Seat

Adz
 Share

Recommended Posts

Adz Experienced

Adz

Posted
Posted

Hello,

I am selling two new Bride Maxis III Low Max race seats. I have just heard production of these seats has stopped so expect prices to rise in the future.

$1650 plus shipping

Located in Melbourne if you would like to pick up.

These are brand new never been used.

PM or phone 0419 504 338

d_f77amf.gif

Link to comment
https://www.sau.com.au/forums/topic/291058-bride-maxis-iii-seat/
Share on other sites
  • 2 weeks later...
  • 3 weeks later...
Adz Experienced

Adz

Posted
  • Author
Posted
im fairly keen to take the other 1 if your seperating. trying to think of somewhere i can sit in 1 in adelaide 1st tho..

As i said to Benji they are the same size of most of the other Bride seats the only diffrence being these have head restraints for added safety.

If you know of a bride seat near by go to the bride seat web page and check the measurments. If its the same width as one close by go have a seat in one.

hope that helps

Downforce Grand Master

Downforce

Posted
Posted

these are awesome seats... if i wasn't taking a break from doing circuit sprints, i'd snap up one of these bad boys ;) if anyone's looking for a genuine bride rail to suit R34 GTT driver side, i have one for sale.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MidnightR32
      RB20DET lean on cold start

      By MidnightR32 · Posted

      I have one and it was at ~43.5PSI.
    • GTSBoy
      RB20DET lean on cold start

      By GTSBoy · Posted

      Put a pressure gauge on the fuel rail.
    • MidnightR32
      RB20DET lean on cold start

      By MidnightR32 · Posted

      I've uploaded logs / the current map to Gdrive if anyone has any ideas. https://drive.google.com/drive/folders/1FPnr22Z-EilG7tYdHSi0Qb07P2jfFLKV?usp=sharing
    • luke gtr
      Spotted on the street....

      By luke gtr · Posted

    • MidnightR32
      RB20DET lean on cold start

      By MidnightR32 · Posted

      I'm running a Haltech Platinum Pro with the stock map for the RB20DET + tweaks for my build. When I started it this morning, the IAT was at 32F/0C (Outside temp was ~42F) and the AFRs went off the scale for my AEM gauge. I let it run for ~30 seconds then turned it off. I then did a smoke test, by hooking into a vacuum line directly behind the throttle body, and confirmed there was no leaks ( i let the smoke tester run for ~5 minutes / confirmed it was generating smoke before hand ). I then started the car again, after fixing a power steering leak.... and it seemed to be happy for ~30 seconds (was at ~11/12), but then seemingly shot back up to ~18 again. I then let the car run for a few minutes, thinking this was just cold start related, but the AFRs never came back down. I didn't let the car fully warm up, so maybe this makes sense, but I'm not sure what to do? The AFRs, when I last ran it, were normal, but because of personal reasons I haven't been able to break in the car. It was rebuilt last year. Engine / Mod list: Supertec pistons Spool rods Kelford 270 cams and Springs Stock crank Deatschwerks 900cc injectors Walbro 255 (Wired directly to the battery relocated in the trunk) NKG Audi R8 Coil packs + Conversion Harnesses from Wiring Specialties Holset HY35 turbo Haltech Platinum Pro ECU Haltech boost controller (wired in for high boost RB25 Neo transmission + needed bits for the speedo to work  
×
×
  • Create New...