Jump to content
SAU Community

How Do I Replace Radius Arm Bushes / Castor Rod Bushes?

islade
 Share

Recommended Posts

08r3308 Mentor

08r3308

Posted
Posted

take them off , take to pedders they will press old ones out and press new ones in ,then you just put them back in

pressing out old and pressing new ones in shouldn't be more than $20

usually if you buy bushes from them its free and bushes at pedders will set you back $105 for non adjustable ones

i got my set done thru them and couldn't be happier great service and quality part , i got mine done in moorebank pedders tho so service will be diff from store to store

bigmikespec Veteran

bigmikespec

Posted
Posted

Definitely go adjustable, I just fitted some today :merli: they look like they wont go in but they obviously do. Ended up using a dowel on the inner part of the urethane bush to try and keep it straight.

Get Superpro bushes.

You need a press to do it, make some drifts out of pipe and away you go.

Mike

666DAN Grand Master

666DAN

Posted
Posted

I had fairly bad luck trying to find anyone to do my ones (Pedders etc etc had laid off workers and wanted 2+ day turnaround) I ended up going to a random servo garage and they let me use their press to do all the work myself.

bigmikespec Veteran

bigmikespec

Posted
Posted

I dont feel the need to spend stupid money for Nismo parts when I can get Aussie made and supported parts, and being adjustable is a bonus. And they are easy as s**t to install just need a press!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      The old manifold was quite under the GTR strut brace.  The new manifold is quite [unknown] the GTR strut brace. The GTR strut brace was needed to clear the bonnet vents. The Old strut brace will almost certainly clear the new manifold, but not the bonnet vents. The old strut brace will almost certainly clear the new manifold, and the new bonnet without vents. But I am hoping the GTR strut brace clears the new manifold :p
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Bonnet clearance?
    • joshuaho96
      Magnetic Drain Plug Snapped in Half

      By joshuaho96 · Posted

      On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, more pain. The FAST manifold is a little larger than the stocker. This is problematic because there really wasn't much clearance to begin with, so going from 'barely enough' well into 'no' is sad based on the external dimensions of the thing, even though where it bolts to the head is the same. Result is the fuel rails sit a good 25mm higher, and this is a bit of an issue with the wiring that runs behind the motor, and the fuel lines, and everything else. When pushing the manifold on, it required a huge amount of force to crush wiring looms to fit it, sensors like the MAP sensor are about 1mm from the firewall, and the FPR just has to bend ABS lines to be forced into place. After some brainstorming and some sad drinking, the loom for some reason ran from the grommet behind the ABS sensor, then to the driver side head, then back to the passenger side head. So all of this was pulled back and stripped, a few wires cut and rejoined, so that the 'branch' was now on the passenger side's head as below: Before you basically couldn't see anything behind the driver head. This is much improved! The MAP sensor is now pointing up (instead of at the firewall) Brackets have been made up for the rail. The rails are for a LS1, the manifold is designed around a LS2 as it's base. Which of course has slightly different bracketry and water pump clearance, hence the mods people need to do. Should be hopefully mounted tonight. I spent money on a new FPR that is slightly more compact than my Turbosmart FPR1200. The gauge has also been moved to the rail. There's also apparently an ORB to AN Union instead of the adapter, because the ~25mm of the current adapter is going to make the difference. Provided this all goes together and arrives today, it'll be the totally not stressful attempt to start it.
    • GTSBoy
      Finding E-30 & E-85 in Sydney

      By GTSBoy · Posted

      This seems like a pointless exercise. There is no E30 availability. Ongoing availability of E85 should not be assumed. Flex-fuel is the only sensible approach, so you can use E85 when and where you can get it, 98 when that's al you can get, and anything in between as you fill it up and drain it down. And if that means replacing the pumps, fitting a flex capable sensor/ECU/whatever has to be done to these Renault shitboxen, then.....so be it?
×
×
  • Create New...