Jump to content
SAU Community

Dameged R35 Gtr In Wa!


striker5950
 Share

Recommended Posts

  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

Ive done quite a few long rears on cars and If i was looking to buy that particular car to repair it i wouldnt be prepared to pay more than 50k for it.....not to sure on what a long rear would be worth with rear suspension ect in it but if had to telly up my labour figure for stripping/unpicking the joins rewelding it,repaint and assemble and id say around 20k.....a long rear is most definatly the best/safest and most unnoticible repair for that car.....

Link to comment
Share on other sites

  • 2 weeks later...
they need moar money!

it is pretty overpriced tho..

true, but if it was me would buy it to swap numbers accross from my cheap grey import (cheap with race only reg just missed a grade 5 one at auction for 5,635,000 yen) and have nearly a complete spare car for parts..... and a fully road registered grey import.. if i was so inclined :D

Edited by URAS
Link to comment
Share on other sites

  • 5 weeks later...

thats a rediculus price , unless there is someone that needs the parts for it, but other than gearboxes not many people need parts , and its not smart trying to part out a brand new car when only a couple of 100 people have the car

Link to comment
Share on other sites

  • 2 weeks later...
  • 5 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Much less twat-tastic. CF wheels are too garish for civilised use.
    • From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...