Jump to content
SAU Community

Recommended Posts

Looking for some fresh ideas.

My brothers R 32 GTR keeps stopping after running for about 3 to 5 minutes.

It just shuts down as if it is out of fuel, then you have to pull over and re start it.

So far we have tried many thing including the following.

- drained and replaced fuel.

- replaced the fuel pump.

- installed the earth bypass on the fuel pump.

- replaced the fuel filter.

- tryed driving it with the fuel cap off.

- replaced the fuel pump relay.

- swapped the ECU.

- spark plugs replaced.

All with no change what so ever, If any one has any ideas of what else we can try or if wore comes to worse , where to take it in Adelaide for repair, we are all ears.

Cheers Trev

Link to comment
https://www.sau.com.au/forums/topic/291535-gtr-keeps-stopping/
Share on other sites

Have you cleaned the fuel tank? Once heard of a similar problem (in a Patrol) - turned out to be a piece of plastic that would get sucked onto the fuel pump. As soon as the engine was stopped, the plastic floated away.

What I think is most likely: Try a different fuel pressure regulator, injectors might be clogged and need cleaning, solder gone bad on an AFM (check DIY section for guide how to fix a AFM)

Long shot: faulty O2 sensor (unplug them both so ECU runs in open loop permanently), I only say this because it seems the car is running fine in open loop while warming up, and when it goes to closed loop it starves itself of fuel and stops.

Check the SA subforum for a sticky with trusted workshops, if you live in the northern suburbs send me a PM i'll give you the details of my mechanic who specializes in GTRs (r32 in particular)

ignition module/power transistor. most common sympton people experience is a missfire however when they get real bad they will intermittetly cut all power to the ignition until it has cooled (generally).

is it difficult to re-start?

thanks guys

The fuel tank was completly cleaned out.

When it stops you need to turn the ignition all the way off, after about 2 seconds you can hear a faint relay clicking noise from around the ECU area. You then turn the ignition on and the fuel pump seems to run for an extended period ( as if it has not been started for a week ). Then you can restart it and drive it home using minimum throttle.

Last night it was started in the drive way and left idiling for 15 min ,it then started to splutter and barley keep running.

we can swap my ignition module over and eliminate that in the next couple of days.

cheers Trev

changed the ignitor last night as it was an easy swap but no change.

Contacted alarm installer and Alarm is only connected to starter motor and not ECU.

We will start looking at the rail pressure and regulator next as well as the AFM,s.

may also give unplugging the O2 sensors a go.

Cheers Trev

Edited by GTR Trev

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh... literally every time i jump on a forum, see an instagram post or see an engine bay at a car show, i get an idea and add it to my 'to do' list. So what started off as, hey can u just make a couple of intake hard pipes because my dumbass bought the wrong apexi kit, blew out into a 2 week job including braided brake lines & custom bash kit for the front lip haha.  Getting Luke from A4E engineering to make a full custom exhaust with a controllable aes dump valve so i can actually switch between quiet and loud, because right now its just loud all day every day. Then after that go and get the tune redone flex e85 & 98 as i get bugger all milage from e85, makes going for longer drivers difficult
    • Car looks clean as. You ended up getting quite a bit done 😂  So what's the plan for the exhaust? 
    • The only Neo rods that were any different to any other RB25 rods were the DET ones, and they were the same as RB26. Here is a Neo DET rod. O5U part number visible. Here is a post in a thread here on SAU with evidence from someone who has done this before. There are photos in the thread of normal RB25 rods.  
    • Sure, but why assume that will be the case forever? And why assume you'll be able to do an oil change to swap back to a stock drain bolt before that happens? And does it even matter when I change the oil at fairly short intervals? Life can be funny sometimes and unexpected things can happen. Like breaking a collarbone so you can't do any work on your car for a few months but the oil change is due so you have to take it to somewhere and hope they don't do something stupid like stacking the new drain plug washer on top of the old one.
    • Do u know how to identify the rods are rb25 or neo ones? Can u look into the pics and tell me is they de or de neo ones. Its confusing becoz my motor has de neo head but block is 25de 75t, so really confusing me about rods, crank.
×
×
  • Create New...