Jump to content
SAU Community

Recommended Posts

  • Replies 83
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

im in melb i can come pick it up also need the glove box front sway bar heater core unit inside the dash all the carpet boot trimming charcoal canister and air box and snorkel and drive window switch no 0403011187 thanks mate really need all these things

Hi, have you still got your tail lights?

Where can i pick them up?

Thanks DAnnie

so i have decided to wreck my r33 instead of fixing it after crashing it. everything for sale is in good condition unless stated otherwise. listed below is everything i can think of but if you need something not listed pm me or call on 0400119068. all interior parts are ready now (12/10) and will have things like motor and gearbox out by the end of the week. i will post pics up on request. feel free to make an offer but im not in a hurry to sell so dont bother low balling!! cheers, Shane

gcg turbo- sold pending payment

engine (inluding front facing plenum)-1300

gearbox-1500

front brake set up (rotors and callipers)-350

back brake set up-150

front subframe-250

steering rack-100

apexi coilovers (adjustable damper)-550

rear subframe + diff (shimmed)-500

front seats-200

rear seat-50

pedals-50

passenger door-120

drivers door (panel damaged, good for window and interior)-70

spare driver door (bought it to fix the car)-100

spoiler and boot-200

seat belts-100 the lot

s2 head lights. (2x left and 1x right)-250 each

fuel tank-50

tailshaft-100

heavy duty clutch and flywheel-100

brake master cylinder/booster-100

front 1/4 panels-120 each

side skirts (right side one slighty damaged)-50

white line swaybar-200

full exhausted system including front+dump pipe, high flow cat-500

big injectors-300

split fire coil pack-300

roll cage (half cage with side intrusion bars made by brown davis)-1000

17inch g-max rims (no tyres)-500

loom-100

tail lights-60

starter motor-40

defi water temp and oil temp gauge + defi control unit (missing oil temp sensor)-400

speedo cluster with 106k on the clock-150

would you have the round thin plate with a wire ribbon that sits behind the steering wheel that plugs into the airbag computer is about 2 or 3 mil thick and about 100 mil across is black with yellow info sticker on it if you have how much with postage to tassie thanks you can contact me on 0408802254 or pm on here your call

  • 2 weeks later...

Ill take the seat belts if they aren't already gone. Id also like some interior trim (handbrake boot, gearstick boot, carmats...) you name your price

  • 2 months later...

hey mate

i am after a piping that goes from the ic piping to somwhere (i dont know) near the stock bov.....

here is what i am after

post-37912-1268351673_thumb.jpg

if you have it them pm me please

  • 3 weeks later...

Hey mate i know its an old post,

But just wondering if u hav any of these parts i need??

- Frount passenger side quater panel

- The inner Frount gard Lh side were the cooler piping

goes thro and were the head light bolts up

i need that whole section

- S2 LH side, headlight

- Radiator suport bar

- frount reo bar, infrount of cooler

Any help would be much appreciated

if u hav any of the above send us a msg on 0403 236 931

cheers troy..

  • 2 months later...

im after the Heater AirFlow Direction Mode Actuator (underneath the dash passanger side above centre heater box) & a Heater Temperature Mode Actuator (driverside on the heater box pedal lil black box)..

if u got both of the PM me plz with a price from them..

cheers,

Robbie

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I wouldn't look too hard at what they did with the R32 GTR in endurance racing in Australia... Lots of things weren't actually available from the factory in the way those cars ran them... Japan also followed what Fred Gibson was doing here with some of there endurance cars in Japan... Australia is also the reason for things like the Brembo brakes, and the change in the gearbox... And quite a few other tricks they used to pull. There's a few other SAU peeps still on these forums that will have heard the stories direct from Alan Heaphy, Fred Gibson, and Jim Richards when we were lucky enough to have a great dinner with them
    • For all the talk of "these parts are junk" I generally recommend OEM because it's really not as bad as claimed. I have never seen or heard of a case like the N63 where the oil returns completely clog with coked oil for example in ~10 years or less. Would it be nice if it were a straighter path? I guess, but most modern cars use a scavenge pump instead of a pure gravity return. Also the factory lines that would be relatively simple to convert to braided are generally speaking hardlines from the factory. I would consider braided line to be a regression, not an improvement. It's also been engineered such that all the hardlines have appropriate strain relief where needed. There's absolutely room for improvement, for example the HKS advantage heritage intake piping shows just how much can be done to make the turbos fight each other less in OEM twin turbo configuration and reduce compressor surge but it's rarely a simple/straightforward process. I recommend looking at what the group A/N1 cars did, generally speaking the changes they made were necessary and proven in endurance racing.
    • Yes, multi relays needed, and possibly a diode. I'm not actually going to think about it though.
    • So I'm confident in saying its TCS thing. My new cluster I never realized didn't even have bulbs in the TCS or Slip slots. Shining a light through the backside that black plate has nothing for it, unlike my original cluster. Looking at the service manual the only thing that stands out is TCS in relation to the vehicle speed, it has nothing to do with turbos. It sadly looks like I may just need to get the appropriate cluster.
×
×
  • Create New...