Jump to content
SAU Community

Recommended Posts

Also go a NIStune over a Greddy E-Manage. You will find the Nistune has a lot more support and tuners then the E-Manage.

Otherwise if you are going to manualise and have a 25det grab a Power FC.

Also go a NIStune over a Greddy E-Manage. You will find the Nistune has a lot more support and tuners then the E-Manage.

Otherwise if you are going to manualise and have a 25det grab a Power FC.

My car is a manual... PFC was in my considerations

  • 10 months later...
other way round buddy.. pick your tuner befor you purchase an ecu.

most tuners I know wont touch certain ecu's becuase THEY know if it will work for them to acheive the best result's

would be pointless speding 1k+ on a part to be told they dont want to work with it.

Except the problem you find is every tuner is biased toward a specific ECU ... I would be getting your head around tuning aspects (most new ECU's all do the same job, rich/lean/stoich/WOT/timing etc.) then you're less likely to get screwed without a reach around :D

To the OP, Hyperdrive are definitely the tuner you should speak to! Oh wait... :)

Lol wow, back from beyond dead!

Yeh, car is now complete. Ended up doing complete GT to GTT conversion.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are certain tasks, like replacing head gaskets, where it is very much best to already know what you are doing, and if you are not already an expert, then the next best thing is to have an expert around to help it get done. Little annoying checks and steps that are easy to forget or not interpret the results of properly, etc etc. It is hard to convey that to someone as a lesson prior to taking on a job, because there can be a whole list of "if you see this then it means that", or "if this is what you find then you will need to do these other 4 steps first". All the little bits of knowledge around sealant choice (ie, sealant at all? or no sealant? sealant only in certain parts of the gasket? sealant for this type of gasket but not that type of gasket? etc etc) cleanliness checks and methods, surface straightness and finish checks and methods, etc etc, all combine to mean that people who have done many of the same type of job will struggle less to get a good result than someone who hasn't done it before. I've been around this stuff since forever. But I will still consult with my expert(s) before taking on the big stuff with higher risk profile.
    • Well if I end up having to do the head gasket I will certainly find the necessary tools and instructions before beginning... Let's hope it won't come around.   Definitely. Depends on the job but I think "if you want it done right, do it yourself" applies almost every time
    • Can you at least move to a location without so many ladders, black cats and mirrors precariously propped up ready to be knocked down? Or buy yourself a 1 ton bulker bag of salt to drag around with you. Just, you know, sling it over your shoulder?
    • Meh, what's the worst that can happen? If is is supposed to have a washer, and: the spring retainer seals reasonably well on the surface, maybe just allowing a little bleed of oil out, and the spring does not coil bind when compressed that little extra bit, then the end result will be slightly higher relief pressure setpoint, and no other noticeable effects.
    • Weirdly I see a flat washer on aftermarket pumps but as you said it doesn't seem like new OEM pumps have it. EPC doesn't break out the regulator as a separate component either. I'm guessing if the pump came that way it's safe to use as-is. 
×
×
  • Create New...