Jump to content
SAU Community

Recommended Posts

surely not, its only an orange car you drive

question for abe and craig

*snip

ermmm, i dunno.... next week sometime APPARENTLY.....

ill know more when i visit to drop more goodies off, ill let you know asap.

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

surely not, its only an orange car you drive

question for abe and craig

when did you say you needed a tow?

reason being i was last ditch for work - i have to go to whyalla on monday. the guy im workin with is leaving tomorrow (to do the full 2 weeks - thurs to thurs) and i miss out on 3 days worth for other reasons

wont be back till the 25th, so im out until then

ASAP would be good, but if you cant...you cant. Just as long as it is done BEFORE 1st March - as i have to give Dion his car back before then.

lol i thought that was a fake site to look the same but its actually real, if you move the cam up n down the street ya can see em waiting in there deck chairs and then chasing it down the road when it go's past.

lol i thought that was a fake site to look the same but its actually real, if you move the cam up n down the street ya can see em waiting in there deck chairs and then chasing it down the road when it go's past.

makes me wish i was ready for it when the google car came past my place... i was just standing out the front lookin stupid

Anyone know when the next Motorkarna is being held? I'm dying to get out and give that a crack! RWD and 4WD :D

I had a look at the Cams website, and I had a look for Moto at Monarto on google and jack diddely squat came up :P

Unfortunetly abit too far for me living south but a christies, seaford, noarlunga or hallet cove etc would be good.

kye, get in touch with MR RS4, he works at woolies down south and might be able to find out for you.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • This piece is obscenely discontinued. I honestly hate the frameless window design because the rubber gets stressed and the guides as well every time you open and close the door.
    • I wouldn't be concerned at all, other than to suggest having them flow tested when you receive them to confirm they are reasonably similar, and then put the highest to lowest flowing ones in cylinder 6,1,5,2,4,3
    • I’m only posting this cause I thought I had seen a bad review on these somewhere before. Any feedback? Would you guys recommend that if I do buy these I send em to RC to have em checked before installing. Or any other suggestions?   https://www.ebay.com/itm/114009965865?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=JDl-15yLQ8C&sssrc=4429486&ssuid=QTzlFXB1S-S&var=&widget_ver=artemis&media=COPY
    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
×
×
  • Create New...