Jump to content
SAU Community

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

ddl.jpg

^ this is what all of the 33 and 34's I've plugged in to have had, supposedly 32's also have the same connector.

Correct. Nightcrawlers R34 GT-T had an OBD1 connector, which surprised me as I was almost sure that all 34's had OBD2

Check under your dash's fuse area, that grey connector should be right near it

-D

Link to comment
https://www.sau.com.au/forums/topic/291893-ecu-error-codes/#findComment-4879201
Share on other sites

Do u know how to clear them nick? If so what suburb u in and how much?

The software I have has an option to clear air bag codes, I've never had an air bag error to test it though.

I'd be willing to give it a shot, Highbury after hours or Frewville during my lunch break, no charges :down:

Link to comment
https://www.sau.com.au/forums/topic/291893-ecu-error-codes/#findComment-4879420
Share on other sites

The software I have has an option to clear air bag codes, I've never had an air bag error to test it though.

I'd be willing to give it a shot, Highbury after hours or Frewville during my lunch break, no charges :down:

Wow, which software is that? Sounds like it must be CONSULT2 compatible to hook into the ancillary ECUs - unless its just OBD2?

Generally speaking most of the software out there (non-commercial) will only do CONSULT1 which is fairly limited in what it can talk to and do. On most cars I've played with on CONSULT there are quite a few other ECUs available via the bus, but require you to use the CONSULT2 protocol, which isn't very well documented (if at all). When you do an initial query, it'll list all of the ECUs you can talk to... (Seem to recall 'EF' is the main ECU, but there's also stuff like SRS, TCS/ABS/HICAS, AT, etc)... Anyways ;)

Link to comment
https://www.sau.com.au/forums/topic/291893-ecu-error-codes/#findComment-4879496
Share on other sites

Does anyone have any pictures of where exactly the OBD port is located on a 32 GTR? I've looked all under my dash, near my fuse box, everywhere... but can't find it!

And the net only shows the actual plug but not exactly where it is :)

Fusebox Above your right knee, port is above the fuse cluster, to the left.

-D

Link to comment
https://www.sau.com.au/forums/topic/291893-ecu-error-codes/#findComment-4879761
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Oh, yeah, look - here's the thing. You always replace the tensioner when you're going in there to replace a belt....under normal circumstances. You want to make sure it is good and safe, and that you don't create a reason to take the front of the bloody motor apart again. But in this case, OP is replacing a belt that has aged out on time, not usage. The belt is a million miles away from aging out on usage. The belt gets a time "limit" merely because it is made of rubber and can degrade naturally. The tensioner? Not so much. I reckon it could last forever on the current usage pattern. So I reckon if the thing is going to continue to get used at the same rate, replacing the tensioner is somewhat gratuitous. Would I replace it if I was doing it on my car right now? Hell yes. Because my car does 10-20 thousand kays a year. So it's all going to be the same thrashedness. Would I YOLO it on OP's car. More than likely.
    • I dunno. I think any one of those from each side to sump is probably enough. Remember - this is about creating a path for gas flow up from the sump to the cam covers. That gas flow then has to leave via the lines to the catch can. There's probably little point in providing 100% more capacity from sump up to covers cf. what you have from there to the catch can. Put in the 3 convenient ones? Any which way that you see fit. That'd be my thoughts.
    • Getting holes drilled into to cam covers and AN10 fitting welded on. My sump has 2x AN10 fittings on it already. These are the options I have come up with that can be done without needing to remove the sump to add more fittings. In all options front of passenger side cover connects to VCT head drain bung (i know this isn't the best spot but my feeling is it must do something). Option 1 (pink). The back of each cam covers gets its own line to sump. Option 2 (blue). The back of each cam covers are linked and share a line to sump. The front of drivers side gets its own line. Option 3 (Black). Drivers side are Tee'd together and share a line to the sump. Passenger side rear gets its one line to the sump.
    • I'd be surprised if Nissan doesn't mention it in the manual as it seems unlikely that a tensioner is going to last 200,000km.
    • Tapin,    So got mine up and realize a few things. First was my slave line doesn’t reach the other side, so I have to get a longer hose made. I want to ask did you have to extend your wires for the CD009 sensors? One on the driver side(right side of car looking at the car from the rear) and one on the passenger side( the left side of car from rear). And do you know what those two sensors are respectively? I know it’s not Speedo since we talked on this already. And I may have to separate the trans again to swap out throw out bearing. We will see. Did you run your RB slave cylinder? I know you cracked your original but replaced it with a nismo. But wasn’t sure if you bought the one designed for the CD009 or not. Thanks 
×
×
  • Create New...