Jump to content
SAU Community

Official NSW Skyline spotted thread


CerealKiller

Recommended Posts

I checked it out a while ago; looked like well in excess of 7k. headlights themselves are ~2500 IIRC (for genuine new GTR).

hmm i may just stay with the 33 front end especially being non turbo im a just sell it soon to get a turbo anyway doing anything expensive to it will just be lost money

Link to comment
Share on other sites

I checked it out a while ago; looked like well in excess of 7k. headlights themselves are ~2500 IIRC (for genuine new GTR).

Actually (as I'm more of a go than show individual) it was a pretty cheap job.

The complete fibreglass kit was $900 from a member (Drift Shop i think) here, the headlights also from a member here (non-xenon) were $500ish, and then the sandpaper, grease/wax remover and cheapo satin black spraycans, sikaflex, pop rivets and cable ties (lol!) added up to about $100 :cheers:

The installation was fiddly to tell the truth, but fairly straightforward. After a dry-fit, and Pre-drill for the mounting holes, all of the panels needed a cut or grind here and there to sit correctly, which I ecpected for a cheap kit. The Moulds seem to be good quality, but some areas had more resin than glass so due care was required. The headlights fitted nicely with some simple DIY aluminium brackets, but still require a bit of fiddling to get the alignment perfect. The original rear arches were cut, folded,and weld stitched before sealing (Room for 285 rubber!:banana:)

I might get some build photos together and post a thread on it in a week or two.

My goal was mostly to get more wheel/suspension room, and to look tough from a distance, and have (mostly) succeeded. That said, if you like show cars don't bother with a cheap kit as you will spend weeks getting a perfect fit/finish unless you have lots of time, money, or bodywork skill.

It's a long way from finished, and my family car/daily and my 3yo daughter loves it! :yes:

Link to comment
Share on other sites

Ah, see I was more looking at getting it perfect R34 GTR front end.... plus I'd need it to be installed as I am the suck when it comes to bodywork :)

I think a lot of that was labour, but yeah, new 34 xenon's are friggin pricey. given that the price of doing the conversion would be basically the cost of my car (sigh), noooot gonna bother anytime soon.

Link to comment
Share on other sites

saw a few today.

- gunmetal/dark grey r35 on james ruse drive at about 4.00 pm ish.

- yellow r34 coupe turning onto shaftsbury rd in burwood not long after

- white 4 door r34 not far behind the yellow one but it kept going down parra road

- r33 parked in hurlstone park near the pub

Link to comment
Share on other sites

WooHoo!

Thanks dude! Where were you? I can't remember seeing a white 33.

I was in a green 2011 fiesta lol no licence for another 3 and a half weeks :-(

Sexy looking stagea tho... Love the plates to..!!!

Link to comment
Share on other sites

Should also add, spotted some very nice Skylines at Sydney Dragway last night!

This includes XKLABA who was out making the high powered GTRs look bad!! :P Pretty impressive runs and an update to that signature block required!!

Link to comment
Share on other sites

Should also add, spotted some very nice Skylines at Sydney Dragway last night!

This includes XKLABA who was out making the high powered GTRs look bad!! :P Pretty impressive runs and an update to that signature block required!!

thank you, you did really good to with a new pb and an impressive trap speed, that 10 can't be to far now, :thumbsup:

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Pretty simple question. I was about to put the transmission back in and thought I pretty much had it lined up when I noticed it seems like the pressure plate isn't flat. I was pretty careful when undoing the bolts both during initial disassembly for cleaning and when torquing them up for installation so this is pretty discouraging. I'm not sure if I accidentally bumped the pressure plate with the input shaft and bent it somehow or if it just showed up this way. Is it possible that there's just something obvious I'm not doing correctly? I'm pretty sure I was extremely careful to make sure the friction discs were seated correctly in the hub, everything lined up, flywheel torqued according to sequence, the little springs all sitting correctly in their seats, etc.  What's the play here? Do I jump straight to a new pressure plate?
    • OK. I can see that being the case. But if you live in the land of "only switching between 4.08, 4.11, 4.36" like most Skyliners, then you never encounter it. Now I perhaps understand why the crownwheel is thicker on some of the smaller numerical ratio diffs. The two stubs being the same (unequal) lengths and just swapped side to side between the different cases is a new one to me. I'm hating Nissan R200s more than ever now.
    • Reason I say this is I have seen broken ones, in drift, drag and even behind a stock Z. I do appreciate most of the time its the synchro's that go.   Trouble with quoting HP is it doesn't really say how strong the box is.  I've not seen many CD00X box's make it past a mid 9(150mph) I have seen about a stock R33 RB25 box's run a 9 too, they all go boom at some point though.   Another clue is they make gearsets for CD00X box's too, wouldn't be a market if they didn't break or have a limit people are going past.   I totally agree it is a strong box, just have to weigh up the true total cost of the conversion vs rebuilding with a good gearset. 
    • What makes you say CD009 boxes are not as strong as you would think? I've always been told the last revision (CD00A) is good for 1000whp and I have no issue's believing it when comparing one side by side with an RB25 box. Makes them look tiny. 
    • I picked up an open Center with shafts. I was told the Open shafts will fit a mechanical LSD and looking at them. I think they will work. Will update 
×
×
  • Create New...